Search results for query: *

Hey guys, I recently got my car back on the road after doing a bunch of stuff to it. It now has a rebuilt 400, A rebuilt A518 with a JW Ultrabell, Brand new driveline and a rebuilt 8.75 amongst other smaller stuff. I've noticed that the car has a vibration in 1st-3rd (before going into OD...

Hello, I need the release cams and rod bearings for the rear seat in my fastback. They are secured on to the square rod by a set screw. Thanks.

Selling my barely used QA1 single adjustable shocks (ts501/ts901) off my 69 barracuda. They have less that 150 miles since installed. I lowered my car a bit and now they are to tall. There are some marks on them and a place on one of the rears where the new stock replacement gas tank rubbed on...

I am swapping a 400 and a A833 four speed into my 69 Barracuda. I am coming from a small block auto setup. Looking for: bb bell housing entire shift mechanism and linkages Thinking of doing a hydraulic TB so the z bar setup not crucial. anything else related to this setup. Thanks

I have a brand new, open box, master rebuild kit for a 741 case. Comes with brand new 3.55 ring and pinion. $325 shipped OBO

Reserved

Looking for a window regulator for the small window behind the drivers door. Thanks.

So, I've been trying to drive the barracuda more lately, and all of a sudden, after two days of driving it, it doesn't start. I jump it, let it run for 20 minutes and then let it sit for most of the day. I go to pull it in the garage at the end of the day and it's dead again! I jump it again...

Hey guys, I have a lokar flexible filler tube for my 518 that i bought second hand and i don't know if i was had buy the seller. My question is: how far down past the filler housing is the dipstick supposed to protrude? The one i have barely (1/8", maybe) peeks out below. It is basically...

I need a filler tube and dipstick for an a518 transmission in a fb barracuda. I currently have a lokar flex filler tube and it sucks. Thanks for the help! Grant

How sacrilege would it be to paint the trim on my 69 barracuda to body color. My taillight housings fairly pitted and the car is nothing but a driver. Has anyone done this, and if so, pictures please. Thanks guys.

Yep... another one looking for an oil pan for a big block swap into a 69 Barracuda. Looking for #187, 699, or 971 (w/pickup). Preferably with minimal dents, twisting, etc. My zip is 99320, so if you could PM pics and a shipping cost that would be great. Thanks!

This came with a motor I recently purchased. It will not work with my current setup. Comes with: Weiand Intake Dual 500cfm carbs Rebuild kits for carbs Velocity Stacks $800 + Shipping Not to familiar with this set up, but feel free to ask questions and I'll do what I can. Thanks for looking!

1965 413 exhaust manifolds. $50 + shipping

Hey gentlemen, I need some big block camshaft gurus. I just picked up a freshly machined 400 that comes with a lot of new parts. The entire engine is torn apart and I think it would be a good time to adjust parts if necessary. Here's what I have: 76 400 block bored .60 over 440 Source...

Need just the offset leaf spring hangers. Must accept PayPal, I've been burnt already this year. Thanks

I went to a large Pitman shaft steering box now i have to get the parts to match. Let me know what you have. Thanks, Grant

I need some torsion bar locking clips for my 69 barracuda. Thanks, Grant

Can anyone help me identify these brakes. The part number on the calipers start with a K-H, so I figure they must be Kelsey Hayes. They are a 5x4.5 pattern.

Possible? Benefits? Has to be done when upgrading to tubular control arms and LBP disc brake setup? I believe my linkage has the idler arm that is a stud on one side and a bolt through on the other. I have been led to believe that this was on the 67 barracudas only, therefore I might have a 67...

So I just got back from the Seaside Muscle and Chrome show down in Seaside, Oregon over the weekend and came away with the "One Cool Ride" award! This was my first real car show and with all the imperfections on the car I didn't think I would come close to an award. I must have got the blind...

So I just got back from the Seaside Muscle and Chrome show down in Seaside, Oregon over the weekend and came away with the "One Cool Ride" award! This was my first real car show and with all the imperfections on the car I didn't think I would come close to an award. I must have go the blind...

ISO: SBP 14" Rim for spare 69 barracuda fastback heater controls Thanks.

Not sure about the color, was looking for more of a charcol or gunmetal color but I think the anthracite grey is growing on me. Cool thing is, is that I can peel it back off if i want to go back to aluminum or just layer on a different color.

I have a Carter competition 750cfm carburetor with mechanical secondaries, and a 360 bored .30 over, moderate purple cam estimated 300hp. Automatic a518 trans, 3.55 and 4.10 gears (3.55 currently in the car). The car is 100% street rodder, is this carb to much for my setup? Would vacuum...

I need a passenger side axle flange with axle play adjuster. Does anyone have one or know where I can get one? Thanks, Grant

So.... On my 1969 Barracuda I changed my turn signal switch because I didn't have any turn signals and my flashers didn't work. After installing the new switch I miraculously had Turn signals (hooray!). Next on my list was getting the emergency flashers and brake lights to work. I do have a...

I am loooking for two these. It is a clip that secures a lever arm in the door latch mechanism. Thanks in advance! Grant

I need a gas tank for my 69 barracuda fb. Mine has a terrible amount of rust in it. Thanks!

What should my cylinder compression (psi) be on my 360? I was told that the engine doesn't have very many miles but I have check three of the cylinders and they read 83, 75, 78 p.s.i. so far. I thought compression should be in the low 100s? Thanks.