Search results for query: *

my w7 junka pump fuel street car engine is done 750 aspirated and a easy 1006 hp with a small hit

just doing a new build for my junk ,thought you guys may like some pics ,its a pump gas small block 4 inch stroke 4.100 bore flat top pistons howards ultimate i beams

hi i have had bad luck over here chasing a r3 block ,do you guys know of any cheers

new pb from the 6 cld turbo

HEMI 6 turbo runs 7s! ~ JUSTA6 - YouTube

new pb in the stock factory cast block,crank and head 6 cld turbo glide 10.5 tyre 7.93@170

1st pass i turned tyres hard and rolled .after that the full pass AP6 Valiant is ANGREE - YouTube

new pb in full street trim std 2 bolt 360-408 ,left lane

got the old banger to hook on the radials,full street trim taip pipes etc on 275 tyre

we ran a 1.18 60 ft [email protected] on the weekend doing some testing in the centura 6 cld turbo 1/8 mile

6cld turbo vid Quickest HEMI 6 - JUSTA6 Chrysler - YouTube

hi after any info on b1 ba with moved push rod holes and mc head , people who have ported them or ran them et ,mph combo , flow number you can pm them to keep private ,thanks ian

some old vids of my 408 http://www.facebook.com/l.php?u=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DzRUt9DxFqjk&h=CAQFvH-hw

http://www.facebook.com/l.php?u=http%3A%2F%2Fwww.youtube.com%2Fwatch%3Ffeature%3Dplayer_embedded%26v%3Da41dU_hnVr0&h=rAQGASJ0oAQHG_BcZ9SznazT-lqshHhBP8HjXIAF0uFmJjA

i have done some porting on the weekend ,i am a truck driver not head porter

we ran a new pb of 8.50@154 in our 6 cld turbo ,check turbo section for info:cheers:

i t ran a 1.23 60 ft 5.5@124 and 8.69 @152 cast iron block , crank , head etc

whats the most hp from a std block ,before they let go

can i get some info on this r3 block p4532907,will my indy cnc 245 ,go on r3 48 degree block with machining more room on the pushrod slots ,can i turn down my scat 4340 360 jernal size to run in it what cubes piston/rods would be best with this combo i will tit it with 200-300 of gas are they...

will the tire height on my 28/10.5 on my 15/8 rims change much going to a 10 inch rim roll out on mt web site is 88 inch mine shows 89.5 my clearance is tight hope to reduce roll out / height a bit .hard to get this to fit on a 65 a body

we had the mopar turbo 6 out a few weeks ago ,sorting her out it ran 9.2@143 leaving slow out off the whole ,this car has a lot left in it i will keep ya posted YouTube - TURBO HEMI 6, SPECIALISED POWER PORTING CENTURA 1ST FULL PASS. CALDER PARK

putting a cage in 65 val not sure on going threw the cnr of dash on front legs , any info and pics would be great thanks

40 degree celces 104 F day ,track temp 62 degrees c had lots of trouble hookin best 60 was 1.58 on this pass YouTube - tnt 10.0@143 mph.wmv

where have they gone can not get on the forum fall over 12 mths

my street car vid 3550 lbs 408 pg 3.89 gears YouTube - tnt 140 mph.wmv

after running a new pb 9.98@134 i thought i will slow down , but i was rong lol this is were i am heading next Attached Images

hi all ,ran a new pb today over the 1/8 mile 6.59@106 was what i ran on my 10.30@132 ran a 6.34 @109 threw the pipes thats close to a 9.99 1/4 .

drag vid 10.30@132 http://www.youtube.com/watch?v=jYEkqBZEgvc

was there was some indybrocks for sale on here yesterday

410 indy headed cnc -1 245 intake runner , cam flat tappet 259/265 @ 050 590 lift and 109 lobe c install 105 , 904 ,5000 stall ,low gear set ,3.9 rear ,26/10 3550 lbs it ran 10.95 @122 asp and 10.30@132 with a sniff now would retarding this cam improve et or not say 112 in stall moving the power...