Search results for query: *

This fan and shroud is made for the Champion 22" radiator for A body Mopar. It is a 14" Zirgo 12V electric fan on a custom fan shroud with neoprene flaps that open to allow full air flow at highway speeds (when the fan isn't needed) and stay closed at slower speed, and when stopped, to let the...

I have a set of newly chromed bumperettes with one rubber insert for a 1972 Plymouth Duster. Bumperettes are in very good condition. Rubber insert is scraped, but complete. Asking $50.00 plus shipping. Located in San Bernardino, Ca.

I have a 1975 Valiant 318 engine oil pan stamped 388. Good condition. Asking $40.00 plus shipping. Located in San Bernardino.

I have the side molding/trim from a 70 Dart swinger 2dr. There are 6 pieces, in fairly good condition with the rubber inserts. Some are a slightly bent, none are kinked. I'm not asking much for these, just don't want to toss something that someone can use. $25.00 plus shipping. San Bernardino...

Hi, I'm looking for a spare tire well and rear lower 1/4 panel sections for a 72 Duster. I saw a vendor that sold these parts very reasonable, but I can't find them now. Anyone have any suggestions? Thanks.

Hi, I've got a 5.9 Magnum in a 70 Dart that won't keep it's cool. It runs cool enough in the winter (around 200+) but in the summer it climbs slowly to 225+. The temp climbs when the engine is under a load, or with the A/C on. If I remove the load (go downhill or pull over and idle) it cools off...

Hi, I want to fine tune the ign timing on the 360 Magnum in the Dart. The cam is a Comp roller with .480/.512 lift and 262/264 duration on 1.6 rockers, Edelbrock 600 carb, accel HEI dist and headers. Mech advance is about 30 degrees @ 2500 rpm. Initial timing was set at 20 degrees with vac...

I need an A/C condenser for 70 Dart or any similar A body (car is modified so I only care that it fits). Must be in good condition. I also need the hard line from evap to condenser in good cond. Also, could use the other lines for parts, so condition isn't that important on them. I'm in So Cal...

I've got a 97 360 Magnum in my 70 Dart with the A/C compressor and serpentine belt assy from the late model, the car has the factory A/C from 1970, I want to hook the late model compressor up to the early suitcase. I need to get a condenser/dryer and have the hoses made up. Will I have any...

Hi, I have an A833 4 spd (70 Roadrunner) that grinds a little going into 3rd. I recently put in a new syncro hub assy with aftermarket rings. All works good except for the light grinding. I think factory syncro rings would solve the problem but I can't find any. Does anyone know where to get...

I need some rubber parts and other items that I got from Paddock in the past. They seem to be gone. Where can I get the kind of parts that they handled... trunk mat, hood bumpers, weather seals, head liner? Thanks.

I'm checking the wiring on my 70 Dart project and noticed that when the a/c fan is blowing, it's not moving much air. The fan motor sounds normal and it has low and hi speeds. It seems fine for the heater but not enough air is moving for a/c. Is there a chance that the vacuum lines have a...

I'm putting a late model 360 Magnum in a 70 Dart. I was going to use a set of Hedman short headers, but the tech guy at Hedman said the LA headers don't seal well on a magnum head. I've never heard of a problem with this before. Has anyone had any experience putting LA headers on a Magnum...