Search results for query: *

1968-72 340 A body. 2863215 18" radiator. Hollander part number 255. I have a few of these but not cheap. same part number as 1968-69 Hemi cars, but those had ink stamp numbers and the later ones are metal stamped. I have the complete assembly with the clutch

let's say your car had a 7-1/4 rear in it to start...with a 904 or 833 it would have had a driveshaft 51.43 inches long. now you're running an 8-3/4 rear, you'll a need a driveshaft that is 48.60. NOW, this is according to my gathered information over the years. if you measure the overall length...

without knowing the original drive train your car had, the length of the original shaft, and exactly which transmission you put in it, nobody can answer the question accurately.

double check all your vacuum hoses. 1 bad air leak from the intake manifold will make the engine die when thrown in gear. your carburetor may be set rich enough that it compensates until you need the power. don't rev up the motor and slam it in gear because the 904 torque converters are very...

I have a 3614368 exhaust manifold dated 3-14-72. NOS I'll part with it for $140. Greg central Minnesota

I'm usually not one to post out of my elements on these MOPAR forums, but I've read quite a few of your posts over the past few weeks, and you seem to be a regular negative 'ninny'. Take this bell housing for example. I've never seen a one of these sell for less than $140, whether on ebay or...

got a pair of aluminum M/T's on a 1969 Barracuda parts car in the lean building. that interest?

I have one from a 1968 Dart if you're still wanting.

I have a bright red one from a 1974 or 75 Dart, but I can't remember how flat it was either. I'm in central Minnesota

if you don't mind my asking, why do you assume your kick down linkage is set correctly? I had a 1974 Road Runner shift like this once, and with a couple turns of the linkage, I had 3rd gear WOT 85-90 MPH. you may not be giving us enough info by just stating RPM's. what are your oil pressure...

I'm in search of a heater control bezel for a 1970 Duster or Valiant. this is te bezel that fit's over and around the heater controls. please pm me with price with shipping.

I live in central Minnesota, 10 miles off of I-94. I have a 1968 383 that ran until parked in 1988, and 1969 that ran until parked in 1991. these both still turned over when I pulled them from the cars 2 years ago. I have at least 3 more that I don't have any history on and may not turn over. I...

I'm pretty sure it has to be 1964-1965 only. I have a 1966 Barracuda parts car, and that one is different than a 1965.

if it's a 1970 engine, the cylinder heads should be cast number 2531894. the J heads are more than likely dated mid 1971 to mid 1972. these are a good head also, and came on all the 360's those years. all 318-340's those years came with the same casting number rods, but the good 318-340 rods up...

I am looking for the secondary hood latch (the long hook piece), that bolt to the hood with 2 bolts. darned if I didn't sell my spare a couple years ago, and now I need one. please email me a picture and price with shipping.

check for a disconnected or rotted through vacuum hose, PVC valve. sounds like an air leak to me at low idle.

selling a nice battery box out of a 1968 Dart. surface rust only, $20 plus shipping from Minnesota 56325

Your ad was deleted by staff....Please read the classified rules before posting again.

I need tail light lenses.... especially the back-up lenses if they're still good. [email protected]

I have a set of 4 speed pedals out of a 1968 Dart. I was told they fit 1967-1976 A body. also have the Z-bar if you need. pm me if needed

let me know if you're still looking, as I may have one hinge cover left. what year is your car? I may also have that hold down bolt. thank's; Greg

Hollander interchange lists 1967 and 1968 doors "non interchangeable". must have different body lines?

do these look right? I don't have any seat to floor brackets/rails

SOLD my wheel adaptors. thank's guy's.

I can imagine people are quite skeptical of these thing's. back in 1990, I bought a 1966 Ford Galaxie 500, 428 Police Interceptor car that had a set of these on. with those, they had the big 5 on 5 Imperial wheels on... why ask why? I never ran the car myself with them on.

here are a couple more pics of that fender.

Hollander says 1967-1969 Dart all interchange with the exception of the trim. 2 and 4 door

here's a picture of what I have. small to large Mopar pattern.

hi again.

I posted a picture of that fender for my Avatar. I couldn't figure out how else to post a pic. it would be great if someone could help me with that info also. thank's; Greg