Search results for query: *

The 4wd in my 06 ram has been buggered for a while. I replaced the tcase motor and it worked for a storm or two. Then it said it was in 4auto, but it never engaged, and i couldn't switch it to any other gear. So today i pulled the tcase motor off and seen that the plug was severely corroded. I...

I have been having nothing but trouble with the 4WD on my 06 Ram 1500 Sport. When I first bought the truck, the "service 4wd" would flash on when it rained, so I pulled the transfer case motor off and found it cracked and full of water. I replaced it, and it seemed to work good for a few weeks...

My wife and I are tossing the idea of moving from New Brunswick Canada, to Miami Florida, because of work. We have family in miami, and i would have a job waiting, and she has an opportunity as a RN to work as well. My question is, how much hassle are we gonna run into, and how does the green...

I am trying to dianose my lack of a fuel gauge. I started with replacing the ground that had come off the sending unit, that being the most obvious. Then, I stuck a test light in the plug for the sending unit, and nothing. I traced it up to the plug behind the d/s kick panel, and the terminal...

Is there an aftermarket rev. lock-out shifter that will fit under a dart center console? Right now I have a quarter stick, but would rather change it out then re-fab it to make it work with my center console. Someone must have done this already, any help is appreciated. Thanks!

My 318 is brand new, using the summit electronic ignition kit (orange box) and a blaster coil. The car starts and idles good, but seems to have no power and will not rev over 3500rpm. I tried swapping out the ign box with another aftermarket standard box, with no change. I am running a 670...

I have a set of 20 inch dodge ram rims off my 2006 1500 Sport. I have them listed on kijiji here in NB, and havn't had much luck. The chrome is excellent on them, but the lip of the rim is starting to corrode a bit on all four wheels. The rubber on them isn't much good, but I am selling them...

I have a mildly worked 318 with a holley 670. The engine is very lazy and I am wondering if it could be a jetting issue. Anybody know what jets I should be running? I believe the jets in it now are 68 front and 69 rear. Thanks

I picked what i believe to be a 78 360 when I bought my tranny with the plan to eventually build a 408 out of it. A friend of mine mentioned that he thought the cylinder walls on the later "environmentally friendly" engines might be too thin to bore out to whats needed. Any thoughts? Thanks

Just wondering if anyone has bought a set of the floor pans advertised on FABO from eBay? The price looks good, but its hard to tell from the pictures what kind of quality they may be. I have seen the ones from auto body specialties and they look good, but are $90 bucks a side, worth it i guess...

Since I bought my demon 2 1/2 years ago, the fuel gauge as always read empty. I would maybe put 5 or 6 litres in at a time just to run it up and down the road. I always assumed there was a problem either in the sending unit or the guage or somewhere between, and thats why it never showed a...

I did some searching, and couldn't find a whole lot. I have changed my ignition system from points to electronic, and pulled my slant 6 for a v8. This picture shows the two wires on the back of the altenator, and I am wondering where they go. I have a simple diagram, put it just shows them going...

I had my 318 running decent a few weeks ago, came out today to move the car, and it won't idle. As soon as I let of the throttle, it dies. Then, even when the car is off, it still spits fuel into the carb. Is it just pressure doing this? Other then sitting for a few weeks untouched, nothing has...

I got the car running today for the first time in about 3 years, backed it out of the garage, put it in 1st and nothing....second and third seem to be there but no first. The tranny is freshly rebuilt, reverse manual valve body. The fella that built it is top notch and I have 100% faith it was...

This has probably been beat to death, but I couldn't find exactly what i was looking for. I bought a new NSS plug with the 3 wires for my 71 demon b/c mine was missing, so to wire it up, the center wire goes to the relay(drk green on mine) then the 2 outside wires go to a bulk connector on the...

What year did they stop using the 3 prong NSS? I have to order one and may be able to get one here at home if they used them in later model cars (80's). If not, it will have to come from the states and take a little longer. Thanks

May be going to look at some parts tomorrow, one of which is a steering column from a console car, fella is asking 150, thats reasonable isn't it? He is also selling a console for 80, and a console w/ shifter for 150. Again, are these reasonable? I have no clue Thanks

My car was originally a 3spd manual on the column, and i have since put a 727 in and floor shifter, but now I can't get the key out of the ignition. First, I can't remember where reverse was on the column, and second, is there anyway to remove the lockout so I can still use the column?

The header, bolted tight to the block, sits on the passenger side steering linkage. Anyone have any suggestions on how to fix this?

About 2 years ago I put an 8 3/4 in my demon with a 741 center i believe. The axles wouldn't slide all the way in so I pulled it out and took a little steel cylinder (slider) out of he chunk, and all was well. Now it is finally time to put a driveshaft in and I want to set the backlash and...

I wired in my electronic ignition the other night, my box is a 4 pin, 2 to the distributor, one to the negative on the coil, and one to the ballest resistor. Then when I was getting ready to run a piece or wire from my positive coil to the opposite end of the resistor, I found a marked wire from...

I just put the calipers on my 71 demon, and the pads looked like they were pretty straight forward, but the outside pad sits on the hub. The inside sits on the spindle, correct? the outside pad sits in the caliper, but when the caliper is put on, the pad falls onto the hub part of the rotor...

Does anyone know where to find the info that big block dart used to have on 8.75 rears and driveshaft length? Their website has changed and the tech page is empty.

Don't forget, clocks roll back tonight, extra hour of sleep before work!!

I have heard a lot of mixed opinions on this. Some say it works, others swear it doesn't. I tried to search it, but came up short. I need to paint my entire interior from dirt brown to black, the metal will be easy enough, but the plastic and vinyl may be tricky, any tips on products or...

Tried to take my steering column out and it just wouldn't come, so I heated the piece still on the steering box(which i figured was a spline) and gave it a pry...nothing, so i heated it a little more and gave it a sharp yank...she come out...but not the way i thought it should...so tell me...am...

fit in an LA Engine. Need head bolts for an LA and they seem to be discontinued, will magnum ones work?

I have a friend who needs the clutch/brake set up from an abody, and I am putting an automatic in my demon. He has the automatic brake pedal set up from his dads Cuda (i think its an E body, isn't it?) Anyways, if i can swap them, then I can help him out and not be out anything. Will it work...

pulling the slant out today and have everything ready to go, now I can't seem to get the tranny to "let go". Tranny is a 3spd manual, I have about a half to 3/4 inch gap all around the bell housing, so all bolts are definately out, but she won't let go. Buddy of mine told me to take the tranny...

Pulling the slant 6 from my 71 demon and putting in a 318, not sure of the exact year of the engine, but come from a 91 1ton. Just wondering the best way to tackle the igntion system. What distributor, do I need an ignition box? Whats the easiest way to make this work? Any advice is appreciated...