Search results for query: *

Hoping someone can advise or confirm my assumptions. I have 2 electric fans and want to have one fuse per fan. When a fan initially kicks on, it draws 43-44 amps for about a second but then drops to around 20 amps. I already have 2 relays wired with a control module from Dakota. Ideally I...

Looking for feedback on the reproduction instrument clusters from Year One or Classic Industries. Not sure if they come from the same place. Reproduction is about the same cost as sending mine off and getting restored but I want to make sure that the quality and fit is good. For a 69 Barracuda.

Rim came from a rust free 69 Barracuda and is almost like new. Very light surface rust where tire bead was in contact with rim. Inner bead width is 4.5" $30 + shipping. Located in Greensboro, GA

Rim is almost like new. Some very light surface rust where bead of tire was in contact with rim. Came out of a California car with no rust. Width across inner bead is 4.5" $40 + shipping. Rim is located in Georgia

All parts came off a 67 Chrysler New Yorker with a 383 and factory air. $25 + shipping for everything. Located in Georgia

$10 + shipping Located in Georgia

I have 2. They have been media blasted and powder coated. $20 each including shipping. Located in Georgia

Original bracket powder coated with new pulley from Year One - never used. $60 includes shipping. Located in Georgia

Parts were new when installed approx. 6 years ago. In good working condition. $100 includes shipping. Located in Georgia.

Includes Brackets, Calipers, and Rotors. Rotors are predrilled for 5 on 4 bolt pattern. Less than 1000 miles on parts. $200 plus shipping. Located in Georgia Link to Scarebird Description of parts: https://scarebird.com/index.php?route=product/product&path=64&product_id=143

Engine builder just finished rebuilding our engine. He ran water through it while running it on an engine stand. I would prefer not removing the drain plugs. Not sure how much straight antifreeze to add to get the proper mix.

We purchased the new rally wheels from Year One and wanted to post a few pics for anyone considering these rims. We got them to put on a 69 Barracuda and purchased the 8" rims which have 4 1/4 back spacing. First they are great quality and look great. No problems finding tire sizes to fit...

We are trying to wrap up a drum to disc brake conversion on the front of a 69 Barracuda. Been quite a few year since I worked on the mid year A body disc brakes. We got all of the necessary parts from a 73-76 donor car and purchased new rotors, pads and calipers. My question is that once...

Not sure when Chrysler changed over to the 2 belt system for big block (383 in our case) engines equipped with AC. Seems like no matter what we do the AC belts squeal/slip when the motor is revved. I understand the reasoning of having a redundant belt but can't stand the squealing. I know...

Has anyone tried these rims? I look the looks of the rims but am not sure about the 4.25 backspacing. Will this clear the fenders and suspension?

We have a 383 with Mopar electronic ignition system and Mopar performance distributor. We were having some problems with the distributor and decided to go back to a stock distributor. The shaft on the stock distributor is 3 1/2" which is supposed to be correct but it is too long. The Mopar...

I just swapped a 383 in our 69 Barracuda (formerly 318) Need some help/recommendations on what to do with the lower radiator hose. The oil filter presents a challenge with routing the lower hose to the radiator. Looks like it would require a sharp 'U' bend to get around the filter to the...

I have a 69 Barracuda with 10" drum brakes that I want to convert to disc on the front. I have spent hours reading posts and articles on this. I used to have a great write up on this but can't find it. I have a set of spindles, control arms and backing plates from a late 60's/early 70's disc...

We are swapping the stock 318 with a 383 and 727 trans. I need to order the transmission cooler lines but there are 2 different sets offered. One has a 'U' bend about an inch from the radiator and the other set has the 'U' bend 12" from the radiator. Can anyone help me with which lines are...

Does anyone know if this place went out of business? They are located in Minnesota and the guy that owns the place goes by [email protected]. I ordered some parts several months ago and never received all the parts :angry7: They don't answer the phone or respond to my emails. I just filed a...

I am doing a 383 big block swap in a 69 Barracuda. Not sure what intake to use. Will the Edelbrock RPM allow enough room for the air cleaner or should I just stick with the Performer?