Search results for query: *

This is a used part in good condition. I don't have the retainer for it. $30 Shipped Paypal Located in West Branch Mi. 48661

This was removed from a 1974 Dart. Included is housing, cover, pigtail, lens, and bulb. $25 shipped Paypal Located West Branch Mi. 48661

Cometic reusable metal head gaskets #245-C5633-030" These were installed with Permatex copper spray on gasket $150 pair A set of custom cut push rods 7.200" long. Number stamped on them is 5002 $35 Mopar thermostat housing # 2780970 $30 Carter fuel pump M6866 $15 Mickey Thompson valve covers $90...

This motor was run long enough for camshaft break-in and has under 20 street miles. All parts were new when assembled in 2015. It was just taken apart on 8-7-18 360 block bored .030" over, block was decked, squared, cylinders notched for rod clearance, new distributor gear bushing, cam bearings...

408 Truck Engine Build COMPRESSION RATIO CALCULATOR Static and Dynamic Compression Ratio (Considers Cam Timing and Rod Ratio CALCULATED DATA Cylinder Head Vol (cubic in.) 3.782 Piston Head Vol (cubic in.) 1.525 Gasket Thickness (in.) .030 Swept Volume (cubic in.) 50.769 T.D.C. Volume...

I'm in row I- 17 with a 2014 5.7 hemi, from a ram 4x4, with only 75 miles. Truck was stolen, wrecked, and recovered. $3500 408 stroker, scat crank, KB 356-030 pistons, Howard's 710581 flat tappet cam, ported J-heads, new 2.02 stainless valves, Summit balancer, 670 Holley. $4000 OBO I still have...

This motor was run in my 1977 Power Wagon one ton, long enough to break the camshaft in and was driven about 20 miles. I used Brad Penn 20W50 along with zinc additive during break-in. Had no problems on pump gas. Intentions were to build the motor for low end torque to use it for pulling a car...

340 cast crank #3751841 (1973/74) balancer, bolt, and washer. Rods 020" mains 010" I replaced this with a forged crank and is the only reason it was pulled. 65 lbs. $100 340 intake manifold #3512100 (1971) was milled so might need a thicker gasket depending on heads. 43 lbs. $100 1970...

Ok I figured out how to post but how do I edit it ? Thanks !

Engine Family: 5.7-Litre / V-8 / Hemi / 395-HP / VVT Ignition: Distributorless/ two spark plugs per cylinder Cylinder Heads: Aluminum with hemispherical combustion chambers Engine: 75 MILES #P04893430OA / TNXE6156411864 (on valve cover tag) The Engine pictured includes the following...

This block was hot tanked a few years ago and has no cracks. Includes the main caps and bolts. The cylinders have a standard bore. The block weighs 225 lbs. $250 plus shipping The crankshaft is a std. forged steel crank and the balancer is included. It may just need a polish. Rod journals...

I just cleaned these up #3751068-2A 1973-74 400-440hp left side $150 plus shipping #2806900 1968-69 B&C body right side $150 plus shipping Paypal is one option of payment Located Mi. 48661 I'll be at Mopars @ Martin May 16th and 17th and can bring these if your interested

I just pulled these off a 318 that I'm parting out. Motor was freshened up and a new camshaft installed by previous owner. The heads are mildly ported with 1.60-1.88 valves. The hydraulic rocker arms and rocker shafts are included. #3769974 $250 plus shipping The motor has zero miles and was...

I was getting ready to install my headers and I put a straight edge across the ports and the left side is straight all the way across but the right side I have about 1/8" gap. Should I bolt them down and hope they will seal ? I tried getting ahold of Flowtech but no luck by phone. Does anyone...

I need a mini starter for a 1977 Dodge 4X4 power wagon, 360/408 with a 727 trans. I'll be using headers also. There are so many different starters to choose from. I've seen them priced from $39 on up. My local parts store wants $125 for one and I'm not sure if it's the right one since they don't...

Looking for the left tail light lense or tail light for a 1974 Scamp. I'm located in Mid Michigan 48661. Just send me a pm and a price please. Thank you

This has about 8 quarter mile runs, 15 1/8th mile runs, and around 250 street miles on it. Had no issues, just going with a chain set up. Mancini and Summit are asking $418. Part #MIL-13600. My price is $250 shipped from Michigan 48661. Consider trades for a 4160 750 Holley carb, vacuum...

This is a 2014 engine with 75 miles. Removed from a 2014 Ram 1500 4X4. It's advertised as 395 hp/ VVT/aluminum heads, distributorless/two spark plugs per cylinder. Comes with intake manifold, exhaust manifolds, computer, and engine wiring harness as pictured. Changed plans and now using a LA...

The truck is in Ewing New Jersey and is going to West Branch Michigan. About 557 miles. If anyone could help me out I'd appreciate it. You can send me a pm. Thank you

I just purchased a set of these rocker arms and the instructions say to use a rocker arm shaft with a hardness of 57 Rockwell "C" scale or "N" scale equivalent. A chrome plated shaft will not work. Anyone have a part number for a shaft that will work.

What modifications would have to be done to make this work ? The motor comes with exhaust manifolds, intake manifold, computer, and harness. Motor is from a 2014 truck being bolted to a 727 trans. If possible ?

I'm looking for the rocker trim strip that goes from the rear of the front tire to the front of the back tire on the drivers side. I'm not sure if both sides are the same but I'll post a picture of the right side.

I'm having a problem getting a link to open in a thread. Specifically an ebay link. Will someone please explain how to do this ? Thank you

Starting bid $9.99 plus shipping, no reserve . Located at in Mich. 48661 http://www.ebay.com/itm/121385503733?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

This was pulled out of a 1974 Scamp and the motor and trans. worked good. The motor was over hauled at 49,000 miles and was pulled out with 98,000 on the car. Included in the sale is the motor, transmission, torque converter, air conditioner pump, power steering pump, intake manifold, carb...

I want to put a manual steering box and column with column shift in a 74 Scamp with power steering. I need to know if a box and column from a 68 or 69 Barracuda will bolt in to the Scamp ? I know that the pitman arm needs to be changed and maybe the crank pulley. Is there anything else that...

I went with the gear drive timing set instead of a chain. I had 1/4" taken off the fuel pump eccentric like the directions said. Otherwise it rubbed on the timing chain cover. The problem is when the gear is slid on the cam there is nothing to stop the FP eccentric from turning. The only thing...

Im working on a '74 scamp slant 6. Changing the K-frame out from a '73 318 Dart. I've already tried the schumacher slant 6- V-8 conversion mounts and didn't like the fit. Now Im putting the V-8 K-frame in and need to know if someone knows the part # of the 340/360 spool mount for the left side...