Search results for query: *

I took my old valve and used the copper seal from it the new valves are from China and seals are bronze and are hard and will not seal .The valve from In Line Tubes was a piece of crap I got one from some one hear on for a bodies only and rebuilt it I had a slit leak at the light switch the...

During the time I was having all the valve issue I was battling power brake busters couldn't make them work my engine was no making good vacuum

I have a 72 Dodge Demon I have installed a hydroboost system with factory 74 front disk brakes and drums on the back . I am on my 4th proportioning valve I have installed two Chinese piece of junk both leaked all over and have rebuilt to factor valve first leaked internally the one I have...

They are sliders

Jack stands are under frame Waco Demon

Calipers are on the forward side Waco Demon

I have a 1972 Demon that I did a disk brake conversion with all 73 a body parts . got my car up on jack stands and when you turn the wheel all the way to one side the line are tight the lines a new 73 dart lines . Any ideas on a longer line . Thank you Waco Demon

Is there any foment about Hydra tech system has any one else installed this system in there car I am look for input I need to put a new brake system in my Demon

has any one used the hydratech brake system . Waco Demon thank you

Has any one installed a can along with a pump to let vacuum pressure to build up so the pump will shut off Waco Demon

Has any one installed a electric vacuum pump for low vacuum and what kind Waco Demon Thank you

Good luck on getting a good new I perches two one of Ebay and one from an online store and both where repoped junk both leaked . I got one off the forum and rebuilt it Waco Demon

We pulled the plug and the light went out .The piston is stuck over to one side the valve has all new O-rings Waco Demon

I have cured my leaking problem . I got a factory valve and I put all new seals in it , no leaks but I now have brake light on the dash that will not go out . We did a revers bleed pushed fluid to the master cylinder getting all the air out of the lines but the light will not go out . Any...

Has any one rebuilt a Weatherhead 3549947 proportioning valve . My problem in the small piston between the two sides of the valve will not come out . The info I have tells you to tap the valve on the work bench or put air behind it from the rear brake side and pot it out . I am not having any...

here is a web sit to rebuild brake proportioning valve www.musclecarresearch.com/1970-76- mopar-combo-valve-rebuild Waco Demon

Yes this the valve I have been talking about .I put both lines from the master cylinder before I slid down into position , I instead the lines jest as In line tubes told me my lines are not leaking it is leaking at the copper washer . I cleaned the block and the input line with alcohol .I...

dose any one else any input on my leaking brake valve problem Waco Demon

My first try with all my new lines I had the same results but the valve was leaking at the hex nut and out of the switch . I got a new valve and before I put it in I checked the hex nut and it was loose . I hooked up all the lines as Inline tubes told me had no line leaks but the hex nut...

I got both of my valves from Inline tubes one from there catalog and other one from there ebay store Waco Demon

the brake valve is the distribution valve some combo valve or the proportioning valve . it is between the MC and the brakes thanks Waco Demon

Has any one had problems with new brake valves leaking . I have a 1972 Dodge Demon did a brake conversion all factory parts new I have installed two new brake valves and both leak I know this one is not leaking at the lines I think at the top where the line from the master cylinder goes brass...

I used a square file and turned the round hole into a hex hole on my 72 Demon

I'm building a 72 Demon I have disks in the front and drums in the back . I have installed all new In Line Tube Stainless lines . We got all the leaks in the rear taken care of but the front end is a different from the proportional block to the front wheels all the fittings are seeping ...

I'm puting Wilwood brakes on my 1072 Dodge Demon . I'm changing the spindels and upper A arms to get the larger upper ball joints . Do I need the disk brack 73/74 spindels to install the Wilwood brakes ? Waco Demon

I'm doing a disk brake convertion using a set of 1976 Aspen brakes . I'd like to know if I can use 73 - 76 a bodie drum brake upper a arm ? Thank you Waco Demon

I found a 76 Dodge Aspen . Will the disk brakes work on my 72 Demon ? If so do I need the lower arms ? Waco Demon