Search results for query: *

got a pair in my ram and love em. drove from wi to tx and back comfortably

the ones that summit racing and jegs sells?

anyone have steering column diagrams for the 70-76? I have a column shift in my car, but gonna convert to floor shift and need to change out the outer column shell where the shift lever goes. I have both columns, just would like reference diagrams to look at

but it obviously has a cardboard headliner I would fiberglass it and re-wrap it with your choice of material.

by looking at the back I wanna say GM, but not 100% sure what did you take em out of?

Awesome, I'm pretty sure my father gas a complete slap stick assembly from a late b-body (Cordoba/magnum) that I can probably get off him that I would like to put in my sport if I can find a console cheap enough

Did a-6 bodies ever come with the slap stick option?

I read they were the same, but wasn't 100% sure if that was right or not.

how hard is it to find a automatic center console for a 70s a-body? my sport has a bench front seat, and thinking about switch to buckets with a center console. also will a slap stick setup work with the console? I can get a slap stick setup, and been thinking on using it in my sport if I can...

the tips on fixing it are good. you could always repair yours with those tips, then cover it with vinyl, that way you can cover the seatbelt holes

wounder if anyones done a fold down seat conversion in a swinger?

Yeah I'd just section it in, still undecided if I'm gonna swap it in though, I might make some fiberglass pods for the underside of the fold down parcel trey (or what there is of one)

Very interesting My currant dart and my old one were both fold down seat cars, I have a spare roof with package tray from a non fold down seat duster and thought about buying that in my currant dart so I can add rear speakers

What electric latch did you use? Mine is from a m-body 5th avenue. Didn't have to do any trimming, just the plastic cover on the latch assembly holds the plastic tailpanel cover out a lil bit

It fits, but it does make the plastic stick it a lil bit more in the center, and after looking at the pic of mine, I might have to fiberglass it to help hid the release and re-carpet it (someone at one point covered the taillight plastic cover with carpet, I like it better then the bare plastic...

Never seen the jack cover before, that's cool!

the dart I currently have and my old one both had the plastic over the tail panel,both with fold down rear seat, and I think they both had carpet glued to the quarters

Will a 67-69 radio fit in a 70-76 dash without issues? Looking at the retro radios that look like an old one with new technology, but can only find em for 67-69 a-bodies

Seat covers are pretty easy from what I've seen, you just need a pair of write cutters, hug ring pliers and new hog rings. Cut the old hog rings off, pull the old seat covers off carefully not to tear up the foam, put the new covers on and pull em right to make sure you get all the wrinkles out...

been thinkin bout adding a pair in my 74 dart sport, but gotta find a pair i like

not unless that was someones fix for busted studs on the backside. every one i have seen has had 4 studs on the back side, one in each corner

but its the easiest and correct way ;)

yup theres 4 speedy nuts holding the plastic bezel on, one in each corner which you can access throught the cluster and glove box openings

he's talkin about the heater controls, but they may not have set screws as my 74 darts heater control knobs are plastic and just push on

the radio has a nut on the backside, and a nut behind each knob, pull them out and disconnect the antenna and wires and it'll slide right out. i beilieve there is 2 nuts holding the heater controls on, plus the knobs gotta come of (on my 74 dart they pulled right off, no set screws) and...

sadly enough that the easiest way as the screw that hold the dash in are under the windshield gasket. i need to replace my the windshield gasket on my dart, but think its gonna have to wait till i get my spare dash chromed so i aint gotta replace it twice

well thats interesting, i thought all the interior sailpanel covers were plastic 8)

any duster, demon or dart sport peices will work for you. if you dont find any in your price range, you could always go for a more custom look and fiberglass em and smooth em out and paint em body color or something

nope, no reason to be in handcuffs ;)

:-D