Search results for query: *

You should open up your own restaurant. That looks great.

:rofl:Yep.

Bolt on parts are ok. Pulling the transmission for a converter swap and a gear swap in the rear end (or a different rear axle) might be too much for many. Hey, at 67 I don't do that stuff anymore either. Like I have mentioned before, I have a LD4B and a AVS 2 in the wings but I am happy with my...

i told him to let me drive.

Dont be scared of plastic in the joints either. Some of these plastics are harder than metal.

See you tomorrow dude ! I shouldn't be sad but I am because it will be another season in the stands unless I hit mega millions

Bet 90% of the cars in this hobby don't and probably never will make over 350 hp. Converter, compression and gears seem to be the mods people want to do the least especially the converter. So for the most part it kind of a moot point most of the time especially on low dollar hop ups.

Bottom ones are also p/s brackets. Kim

Bet you can't make the bumper ends touch around the tree.

I was coming to run my slant, but too far to tow with the rain and storms all around.

Super was late. The wife came home at 8. No worries, it was all done about then. Not too fancy but quite tasty. Rib eyes from Sam's spiced with coarse ground salt and pepper. Potato strips grilled with EVOO on the flat top with onions and fresh corn on the cob from Wal Mart. (quite good for...

Somebody has to tell you, so it may as well be me. :( That is what's known as a 318 Poly motor and it will not fit in your 64 Barracuda, because it is too wide. The 318 Poly motors only came in B & C body cars, and also pickup trucks. They never came in Early A body cars like your 64...

I know it sucks to wait, but it is always best to measure once the trans is in.

"I farted"

Does anybody know who might sell Hurst Super Shifter shim plates and Pivot pin assemblies? Maybe someone can point me out to what is different in the pivot pin assembly? I can tear into another shifter tomorrow and probably answer my own question but thought somebody might know right off the...

my point of contention is that some people just want a nice little cruiser. it doesn't have to be all ricky-racer burning up the tires, just something that's not a wheeze bag. starts easy, runs smooth, has a little more oomph and is still okay on gas. yes, a converter and gears will absolutely...

Looking for a nice set of 70-71 Dart/Demon Fenders. Close to eastern NC if possible. Thanks!!

@HawkRod is putting a group tent together for FXBO folks (from all the sites - under the FBBO banner). Lunch on Saturday for folks to get together. I went last year and a good time was had by all!

Still wanting to contact you. Tell me how to PM - where do I go? Martin

Puck just dropped on Jets game, gotta go!

Error just slightly on the short side so you do not break the tail shaft on transmission going over bumps or rough terrain.

Wife?

Gonna be a long series I think. Nothing flashy, just grit and grind from both teams. Blue collar series. Good tuff hockey.

That's even fewer years ago than I did mine, so my memory may be fuzzy! Oddly, I can remember doing it in my parents driveway, but not the exact method I used. I really had to dig deep in the memory banks!

They got their hands full.

For the non hockey guys on here the reference is to Matt Rempe of the Rangers. Not sure exactly of his stats but he is north of 6-5 and weighs I think 230 or 240 and is actually a pretty skilled guy and fast for a big guy. And he is earning quite the reputation for good clean hits, and has...

Thanks!

Just checked the phone message, Mopars Invade is on for tomorrow!

complete 73~76 disc set up with a V8 K-member, including factory swaybar. everything you need to upgrade any 67~76 a-body. pulled out in favor of an aftermarket set up. the upper & lower ball joints are still in good condition and have lots of life left, you can run the upper control arm...