Search results for query: *

doing a hemi install what oil pan will work best milodon 31015 or 30931

Those should work nicely. My numbers are down on my last two sets because my customers held me back from what I’m used to doing as far as chamber work. Those were my last two sets of heads where the customer dictates that. A 2.08 valve should easily be over 320 cfm without restrictions on...

Heater hoses hooked up. Pressure tested coolant system and it holds pressure. Installed defrost plenum, defrost tubes, and glove box liner and door.

Did you try getting the minimum across the board? How about minimum on the first three and maximum on the last one?

From 1979 technical service bulletins Miscellaneous October 18 1979 number 26-02-79 subject 1979 vehicle identification numbers

I set mine so they contact the padding on the roof (ceiling) so they don't move while the car is running. Would kinda suck if I did all that work and they rattled. And mine is a '72 so it didn't have all the holes in the edges-only the two sets at the back. I assumed the idea was to have each...

How much of a 71 Swinger can you fit in a Durango?

Like this? NOS.

Just joined after watching posts for years. I bought and rebuilt my '67 Barracuda starting in 1995, getting it in it's first show in 2008. Several years ago I had the engine completely rebuilt because of poor gas mileage (13 mpg.) Now I've purchased a complete MSD ready-to-run ignition...

Is there a decent parts diagram that can identify that rear set screw? I don’t know where or what screw that is. Also the idle set screw doesn’t engage and there must be a reason. It is like it’s 3/8 too short but I know that it’s not. Does the carb need something to bring the idel set point...

Not knowing much I’d say you need T slot restricters. Not sure what you have for emulsion but some of those carbs came with too much emulsion and way too big of a main air bleed. A bigger air bleed wi start it on the booster sooner. If your MAB is bigger than .026 it’s probably too big. That...

Ill take them and thanks.

I thought it a bit odd that they would pull all of the products of Speedmaster from the shelves. Maybe a CYA move?

Thanks for that link, I was holding off asking until I determined if it would be needed. My build which typically go zen like has been going off the rails a bit today mostly due to a not so smart 340 block marketplace purchase by me with issues and trying a new machine shop which left me with...

That's it! I'm buying a set of Doug's headers now. They look so much better in quality in the photos. I've messed with crappy headers more than I want to. I had enough of the rust, terrible bolt clearance, warped flanges out of the box and crappy welds that sometimes need repair.

Ill take them and your adress

A set of wheel dollies or tow truck skates and the lock boot and disconnect don’t mean a thing. Gets dragged onto a rollback or into a trailer and away it goes. A cut off or simple ignition ground switch is plenty for stopping a joy rider. Clubs and wheel boots and all that crap are...

PM sent

What would you sell just the engine for? Thanks.

My 71 Demon 340

I revived this post as I'm having a similar problem. running an XP850 and perfect at idle, perfect at WOT, but pig rich at cruise. Like 11 to 1 ish. Light 4 speed car with 4:30 gears. Timing locked at 33 degrees. Tried changing air bleeds, P Valves....all for naught. Jetted primary from 84 to...

it's all part of the process amigo. it a collective effort and, at times, knowing what is wrong can be just as valuable as knowing what it right. the reason i say to call the shop doing the work and verify with them how they wanted it measured is because i got jammed up on that deal. shop i...

I'm saying this with all of the Christian and brotherly car guy love I can muster, so don't take it the wrong way. From your posts, you really need to read up on vehicle electrical systems, Chrysler products especially. I'm not sayin this cause I think you're stupid, but the exact opposite. I...

BB

Just a stupid question. Trust me, this kind of thing happens more often than you think.

Thanks, I'll check that one other thing I noticed when driving it, if you drive along slow and cut the wheel left or right, the wheel will continue to turn that way if you let go and the car will dart in that direction

pretty good numbers. My old Eddy's just came back from a professional porter who just retired from a big name company. I got lucky to get his name. They also have the 2.08 intake. I ran them a couple years as ported by my local machinist. The new guy also did my S Victor. wish I had taken better...

I was thinking about the pinion. Just keep it in R then.

I believe it would on the wheels.