Search results for query: *

I filled up today and thought I would share. I have a 70s OEM supersedes fuel sender (the one that is shaped like the aftermarket ones) in my 18 gallon tank - 67 Dart. The gauge needle was exactly 1/2 way between 1/4 and 1/2 tank or 3/8 3/8th of 18 gallons is 6.75 gallons in the tank 18 -...

In the literature Dodges were branded Charger for the 273 4bbl and Plymouth were branded Commando for 273 4bbl I can not say I have ever seen a Charger branded unsilenced air cleaner on a Dart with a 273 4 bbl. Am I missing something here?

I bought a jet screwdriver to remove some jets from a CARTER BBD carb (I have chewed up too many jets just using a wide screwdriver) Looked good. Wide, flat, and textured. It's going to work great! Put it on the jet and started to turn, a little resistance, ok no big deal. Kept turning then...

I have been looking for a tailpipe sniffer A/F ratio meter. Found this video. This let's you put your O2 sensor into the fixture, insert it into your tail pipe, hook it up to your A/F ratio meter Exhaust Clamp - P/N: 37280 > Universal Accessories > Innovate Motorsports

So I'm getting conflicting info. Was the off the assembly line 67 273 V8 fuel pump rebuildable or crimp style. Rebuildable style Crimp (not rebuildable) style If anyone has a (verified) factory origional pump they can photograph and post I would appreciate it Lastly where would (I...

Got the tank down into my "ruh roh" level Went to the station and filled it up 14.9 gallons. My tank has a dent and only holds about 17.5 gallons (most i ever got in it when completely empty) 14.9 / 17.5 = 0.85 1 - 0.85 = 0.15 (gives decimal equivalent of the fuel left in the tank) 0.15 x 8 =...

67dart, 319,000 miles, original gas tank. Had a hope that I wouldn't have to remove the tank, in the imortal words of Maxwell Smart missed it by that much, about 3/4 of an inch! Drained the fuel from the tank Removed the vent tube Unscrewed the trunk floor grommet. Unscrewed the filler neck...

Very interesting.

Dart 67 recently posted about a sender that he found that was very close to an OEM A Body. It is for a 60's A100, sold on E-Bay, here is his post: Close as you will come to getting an OEM fuel sender.. Post 11, Arron Tate did an awsome wright up of the sender with some fantastic in tank photos...

Doing some tweaking on my fuel sender, 67 Dart. Discovered my 2 year old plastic float had a little fuel inside. I would have preferred to have a copper one but you got to deal with what you have some times. I ordered a replacement float from O'Riley's auto parts, not listed as compatible on...

BBD question... I have a donor carb 1966 IIRC and it has small gaskets under the jets. Mine 67 did not have them when i rebuilt it. Any one use them. It would raise the jets up into the metering rods abit changing the tune. Thoughts?

What do you think... OE 1967 Air cleaner wingnut? I don't know where I found this. It may have been chromed as there is copper showing through in areas of ware. I have not cleaned it. There seems to be carbonized buildup in the recesses.

Hi all you BBD gurus! My 273 2bbl (BBD 4116SA CAP) smells like it is running excessively rich. Forgot to mention I'm at 5000 feet now. I rebuilt the carb 1 year ago, I have put 1000 miles on it since. Drivability and acceleration are normal, idles OK, No stumbiling or bogging down. I may have...

I've been helping a member with his carb issues in PMs. Some of the info and photos I'm posting might be helpful to others. I believe all springs are OE from 67 but I can not say for 100%. My dad did not do any modifications to his car but you never know. I counted 75 turns (I recounted) The...

Has anyone observed the following behavior? I have a clear fuel filter ( ya I know I know) When the engine is at greater than 1000 to 1500 RPM the fuel filter is completely full When the engine is idling the filter will slowly drain till it is completely empty. The engine rpm will reduce until...

I have looked at the typical sources, all seem to offer about the same. What are your thoughts / experiences? Thanks

Recommendations for rebuild kits and misc parts. I have looked at the typical sources all seem to offer about the same. Thanks

Ok all, Anyone ever recover from this situation. I've broken my share of bolts and screws but this time not my doing, I received the carb this way. I have not cleaned the carb properly yet so not sure just how much of the screw is still in the hole. It is a California carb so the adjusters...