Search results for query: *

I have a retro tech fabricated tunnel ram with 2 Barry grant 750 tunnel ram carbs. Carbs have new Superformance gasket kits in them. Comes with all lines, linkages and fuel pressure regulator. It is ready to bolt on and go race. It was a tenth faster than a m1 and dominator on my motor. I...

Narrowed Dana 60. Measures 34" Wilde without axles. It does not come with axles. It has strange spool. 4.10 strange gear. It was built by Gary Reese race cars using all chromoly parts from RJ race cars. Has 4 link brackets. Comes with 4 link bars, chromoly wishbone, chromoly anti roll bar, cast...

I have a 8.75" housing with drum brakes out of a 68 dart that was mini tubed so the spring perches have been moved in. I do not have a center section for it. Asking $400. Located in middletown Ohio. I can email pics.

Weiand low deck tunnel ram in good shape. No strip holes and has never been cut on. Weiand stop producing these intakes and they are getting hard to find. Asking $325 plus shipping. I can email or text pics. Message me on here with email address or number to send pics to. Thanks

Sold sold sold. Roller cam for BB. Cam has about 10 passes on it. It wont work for my new setup so it has to go. Heres the specs Int. ext. .706 .706 273 280 @50 106 lobe seperation 106 installed centerline Valve lash .024 .024 Asking $200.

I have a set of hooker 2" fenderwell headers for a BB in an early A body. A couple tubes were cut and positioned so that they could be used on an early A. We ran them on our 66 dart drag car for a couple years. They do not have collectors on them. $75 plus shipping. I can try to get pics...

I have a K member that has been modified to put a BB in an early A. The motor mounts have been cut off and was setup to use a motor plate. It has been cut out and boxed in so the oil pan will clear. We had it in our 66 dart drag car but now have tubular front end and no longer need it. the...

SOLD SOLD SOLD!!! I found it while I was cleaning out the garage. It came out of our old race car. It is a rachet shifter. I'm not sure what model. I will take $20+ shipping

I have the upper control arms, spindles, 1 caliper bracket, dust sheilds and lower balljoints. I lost one of the caliper brackets when we moved. If I find it I will send it to whoever buys the parts but as of right now its missing. I'm asking $125 + shipping and if I find the other bracket I...

I have a set of 915 heads for sale. I will sell them complete or with just valves. They have stainless valves, tittanium retainers, 10 degree locks. They were built with only the beat parts. The ports were cleaned up a little. They only have about 50 passes on them. Im asking $1000 complete or...

I have a set of 452 heads that are ready to bolt on. They are fresh from the machine shop. All new valves, springs,retainers,locks and seals. The ports have been cleaned up a little bit. The springs are double springs with dampners. They should be good for up to .600 lift. I will also include a...

I have a southwest speed floor mounted pedal assem. with balance bar. It has 2 wilwood master cylinders alreay mounted to it. I used this setup for one year in our car and it worked fine. I will take $115 plus shipping. It cost $200 new.

I have a narrowed 8.75 That is ready to bolt in a car and race. It is 37" from drum to drum. It has Moser axles with 1/2" studs, Strange spool, Mark Mark Williams billet caps, Richmond 4.56 gear. I put new bearings in it before last race season. It probably has 150 passes at the most on...

I have a set of 915 heads I just bought and are not going to work for my build. They are fresh from the machine shop and ready to bolt on. They have new guides, seats springs, seals and stainless valves. The bowls have been blended. They are 2.08 intake and 1.81 exh. they are 67 HP heads...

I have a set of 452 heads that just got done at the machine shop. They have new valves, seals, retainers, locks and double springs with dampners. They should be good for up to .600" lift. I bought an engine with these heads on it and have no use for them. You should be able to put your rockers...

I have a clutch style sure grip thats in very good condition. It has new bearings and races. The only reason I took it out of the car is that we put a spool in the car. The numbers on the unit are "10 10 66 A" "22685X" I will take $300 plus shipping. I think it might fit in a flat rate box...

I have a set of 9" drums that are complete from the backing plates to the drums. The hubs and drums have been drilled for the BBP. They have new wheel cyclinders and new hardware. The shoes and drums are in good shape. I have a new set of screw in studs for them. I had this set-up on my...

I just pulled this from a drag car I bought. I was told when I bought the car the motor was just rebuilt, which I belive because the car was unfinished and was noway it could have been ran in the car. We finished the car and have put 6 passes on the motor and relized its just not enough motor...

These came on a drag car I just bought and we are getting rid of the small block. They are in great shae with minimal surface rust on them. The previous owner had welded pipe right to the end of headers. I cut it off as close to the added pipe as I could. The flanges are straight and sealed...