Search results for query: *

Running a square-back alternator, one field is grounded. I had a mechanical regulator, it worked fine but recently crapped out so I want to replace it with a SS unit. I just need a good part # and source.

I recently purchased a 74 dart, I need a fuse box diagram with amperage ratings. I have schematics from mymopar.com but it does not have fuse layout or ratings on it. I could also use a user manual too.

I've been trying to get the horn to work on the old 68 ragtop. The relay is inside near the fuse box and it seems to be working just fine. I even took it out and checked it on the bench. Anyway, when I ground the horn wire the relay kicks in, closes the switch and sometimes the horn blows...

I need to know where to buy a good quality turn signal switch for my 68 Barracuda. I don't want a cheap Chinese knockoff. I'd also like to know if the "lane changer" option is still available in these switches which allow you to activate the switch without locking it in. It needs to also...

My 69 Barracuda with 904 trans has backup lights that stay on. I replaced the 3 terminal switch with no change. No amount of adjusting the selector fixes the problem. The lights are not on when it's in park but do come on when in Reverse, drive, 2 or 1. The center terminal (NSS) works...

My temperature guage has been flaky lately on the 69 fish car. It would work one day and not the next. Gas guage was ok so I knew the 5v regulator was still working. I had the whole dash out and on the bench where it worked fine... put it back in, it worked for a while then crapped out...

I have a bad ignition switch on my 69 Barracuda. Most of my gauges were not working intermittently and I traced it to the ignition switch itself. I pulled it out, put it on the bench and did a continuity check from Battery to ign1 and ign2 etc. Sometimes it would work, most times not so I...

I replaced the tank sender in the 69 Barracuda a few years back and it's never read correctly. I do have a solid state 5v IVR and it's working just fine. Temperature gauge reads correctly too. Anyway, what happens is the gauge reads full when I fill the tank but goes down quickly to near zero...

I have a RTE board installed on my factor tach in the 67 Barracuda and it's not working. It did work for about 2 days then crapped out a couple of years ago. I finally got around to taking the dash out to see if I could fix it. I verified 12v and ground to the unit and meter movement is good...

I purchased a 4x10 speaker from Classic Industries and am sadly disappointed. I had to replace the old Pyle speaker so I paid top dollar for theirs and expected a quality speaker. Instead, what I got was a cheap Chinese import that sounds horrible. It has a tacky chrome metal base on it and...

I'm using a 7805 regulator as the dash regulator (69 Barracuda) and it heats up after a while and stops working properly. The fuel, temp and oil pressure all show a lot lower than they should until I turn the car off and then turn it back on. The fuel gauge points have been pulled apart so...

I decided to check my gauges while I have the instrument cluster on the bench and I found I'm getting no output from the built-in regulator on the 3-terminal fuel gauge used in the 67 Barracuda. Since I have several hundred 7805 and a few 7806 regulators in stock I decided to give it a try and...

I'm wondering what's the purpose of using a brass feeler gauge when setting the gap on the reluctor in a mopar electronic ignition system. I'm guessing it has something to do with it being non-magnetic but why can't you use a standard stepper feeler gauge?

Anybody know where I can buy new hood turn indicator assemblies for my 69 Barracuda?

On my 67 Fish car I am getting 15.5 Volts coming off the alternator; it seems a bit high from everything I've been reading. The solid state blue regulator I had was acting strange (working then not working) which prompted me to start measuring voltages. I'm running an old style single field...

I have a 67 ragtop Barracuda with no wiper motor. Can I use a 69 wiper motor, is it wired differently?