SOLD***SOLD***SOLD***SOLD
I'm selling my Gen3 project, 5.7 truck block is line honed with ARP hardware, un bored at this point. I have a drag race rotator, Molnar Crank, power adder rods, CP custom dome pistons and rings, King bearings, crank is balanced with a 32 tooth wheel. 6.4 heads...
I have 3 sets of Headers, 2 are TTI B-E body headers, been using them for dyno headers so they are used pretty good, might want to have them re coated...first set is part# 383-178 which are 1 7/8 headers for low deck, 2nd set is part# 440-2 which are 2" tall deck headers. The 383 headers have...
Everything is untouched, 1962 413 wedge, Heads complete, Rockers complete, pushrods, intake manifold, valve covers, carb, and exhaust manifolds...asking 950.00 for everything shipped anywhere in the Cont. U.S.
I would possibly be willing to piece everything apart....
Brian...
Brand new 440 we built, 500HP, 540TQ, Procomp heads, 9.8:1, hyd. flat tappet, forged Probe pistons, complete carb to pan...idles nice with a good exhaust note, nothing crazy but healthy sounding lobe...11,500.00 or best offer.
Brian...
BB 906 heads for sale, Manley stock size valves, perfect castings, our valve job, surface cut down to 79cc, single springs for hyd. cam or solid ft., 10° retainers and locks. Springs are 135lbs. closed and 300lbs. at .550 lift.
Dyno time only!!
$400.00 plus shipping
Brian
400 BB Mopar short block for sale.
Factory steel crank, balanced and 10/10.
Factory rods with arp bolts and resized.
KB flattop pistons and rings.
Block bored, decked, assembled by IMM Engines.
Cam is Comp hyd. Thumpr. Comes with double roller timing set, and lifters.
Dyno time only, made...
This needs to go! I have sold the dist. and wires so it's only intake to oil pan with valve covers ready to run with all the build specs and magazine article to boot.
First 3500.00 gets it and I'll ship it anywhere in the cont. U.S. for 300.00 including the crate!
Brian...
NEW SB Mopar Forged rotating assembly for sale: Scat light weight forged 3.58 stroke, 340 main 4340 crank, Scat I beam 4340 rods, Custom Ross flattop 4.060 pistons, 1/16-1/16-3/16 ring combo with deep valve reliefs, Total seal ductile moly rings, Clevite bearings.
It's balanced internally and...
Selling a 400BB Mopar that was built for Car Craft magazine a few months back
http://www.carcraft.com/techarticles/ccrp_1207_chrysler_b_series_400_hemi_power_at_half_the_cost/index.html
It's intake to oil pan, ready to go...$4500.00 I have the ready to run dist. and wires too if...
I'm selling the 400 we built for Car Craft. Here's a link to the thread on here...
http://www.forabodiesonly.com/mopar/showthread.php?t=179546
It made 427HP and is complete from intake to oil pan...4500.00 and I can ship it almost anywhere in the U.S. for 300.00.
Brian
[email protected]
Will seperate!
Fully ported Eddy heads, flow 305cfm @.700, 2.08x1.60 Manley valves, roller springs, Ti retainers, 72cc chambers WITH TD 1.65 rockers.....$3400.00 DYNO TIME ONLY!!
Rockers only $850.00
Have 11/32 .130 wall pushrods that goes with the eddy heads/solid roller cam and...
Fully ported Eddy heads, flow 305cfm @.700, 2.08x1.60 Manley valves, roller springs, Ti retainers, 72cc chambers WITH TD 1.65 rockers.....$3400.00 DYNO TIME ONLY!!
Have 11/32 .130 wall pushrods that goes with the eddy heads/solid roller cam and TD's...$150.00
Also have 3 solid roller cams...
Brodix B1B1 heads for sale, complete with valves and dual springs PLUS TD 1.6 rockers.
Everything is brand new, no porting or any work done to the heads, just straight OOTB...3000.00 and free shipping in the U.S.
620HP pump gas 414cid sb mopar for sale. This is the engine that's featured in...
*********PRICES REDUCED***********
Brodix B1B1 heads for sale, complete with valves and dual springs PLUS TD 1.6 rockers.
Everything is brand new, no porting or any work done to the heads, just straight OOTB...3K OBO!!
620HP pump gas 414cid sb mopar for sale. This is the engine that's...
Brodix B1B1 heads for sale, complete with valves and dual springs PLUS TD 1.6 rockers.
Everything is brand new, no porting or any work done to the heads, just straight OOTB...3K firm.
MSD crank trigger, new and complete...250.00.
620HP pump gas 414cid sb mopar for sale. This is the engine...
Just finished this 414cid sb stroker for Car Craft magazine. Made 621HP and 541TQ. NO belt drive, dist, wires, carb or headers. Complete intake to pan, with billet roller timing set and std. cover.
Email if interested in purchase.
$10,500.00
Brian
Indy 245cnc small block heads for sale with JESEL rockers. Dyno time only. Heads flow 340cfm at .700 with a 2.100x1.60 5/16 valves. Chambers are 53cc.
Rockers are 1.7/1.6 and also have 1.6 ratio intakes.
Heads with valves, ready to run with rockers, just need springs...$4K
FREE SHIPPING in...
Indy 245cnc small block heads for sale with JESEL rockers. Dyno time only. Heads flow 340cfm at .700 with a 2.100x1.60 5/16 valves. Chambers are 53cc, been angle milled .5°.
Rockers are 1.7/1.6 and also have 1.6 ratio intakes...
Heads with valves, ready to run with rockers, just need...
Selling Indy CNC ported SB heads. 245 intake port, hand ported exhaust ports and chambers, 5/16 stems, 2.100x1.60 or I have 2.15 intakes I can install. They flow 340cfm at .700 lift and the chambers are 53cc. They have been angle milled 1/2 a degree.
Also have Jesel 1.7 and 1.6 intake and 1.6...
Batten W2 heads for sale. 2.08x1.60 NEW Ferrea valves, new roller or FT springs with Ti retainers, 10° keepers, valve job done, 58cc chambers are closed now (welded up).
Pressure tested, no cracks or leaks, guides are 11/32. They flow 281 @.500 and 300 @.600 lift with room in the chambers for...
I've got a set of Batten W2 heads in my shop I'm going to sell.
They are 2.08x1.60, have flow sheet. I don't know who did the porting, but I touched the seats up and replaced 1 ex. guide that was leaking.
They flowed 302cfm at .600 lift, and are oval port. I've heli-coiled one intake bolt...