69 dodge dart glovebox striker

[liznelson]

There's a member I pmed about a photo of his that he got recently I'm going to loop him in here

Yes!!! Thank you so much

 

[liznelson]

http://[URL]https://www.ebay.com/itm/116551279443

[/URL]


Alan

Thank you so much!! I’ll get it ordered

 

[j par]

Myself, this would have been an opportunity to flex my fabrication skills...
Especially being inside the club box...
Of course, unless I was planning on taking it to pebble beach for a car show that required something like that...

 

[Dana67Dart]

It seems like such a someone part that the aftermarket would make it.

 

[liznelson]

Myself, this would have been an opportunity to flex my fabrication skills...
Especially being inside the club box...
Of course, unless I was planning on taking it to pebble beach for a car show that required something like that...

I agree! Just wasn’t sure what should be there cause it’s been missing since my dad had it. I couldn’t even find a picture of what it looked like.

 

[liznelson]

It seems like such a someone part that the aftermarket would make it.

Shoot I might make a few . Thank you again for all your help! Such a piddly little part. Can’t wait to have the door not flop around

 

[j par]

I agree! Just wasn’t sure what should be there cause it’s been missing since my dad had it. I couldn’t even find a picture of what it looked like.

I had the other kind of latch on my duster, the one that you don't have that grabs something and I made it out of a coat hanger wire where I curled the the two ends for the screws and made it the right length after a couple tries... i actually made it a little big, so the glove box door would hang open a half inch, as that's where I had my msd box and my msd start/retard, switch for nitrous... i figured that would let air circulate in and out, so the box wouldn't get hot...
I eventually found the correct one, but, I never did use it..

 

[440 Mike]

Here's a picture of the door/latch/striker that I bought for my 68 Dart.

 

[liznelson]

Here's a picture of the door/latch/striker that I bought for my 68 Dart.
View attachment 1716395186

That’s the one! A guy on here found one on eBay so I ordered it this morning. I guess cudas had the same one in 69. Very tough to find. Might see if I can make a few so it someone ever runs in to the same problem

 

[liznelson]

I had the other kind of latch on my duster, the one that you don't have that grabs something and I made it out of a coat hanger wire where I curled the the two ends for the screws and made it the right length after a couple tries... i actually made it a little big, so the glove box door would hang open a half inch, as that's where I had my msd box and my msd start/retard, switch for nitrous... i figured that would let air circulate in and out, so the box wouldn't get hot...
I eventually found the correct one, but, I never did use it..

I worked at a scrap yard for 18 years and went down there to see if anything was even close. All were the wire/rod type. Glad I was able to find one. Paid out the nose for it though

 

[Dana67Dart]

. Glad I was able to find one. Paid out the nose for it though

Once in a lifetime purchase

 

[liznelson]

Once in a lifetime purchase

True

 

[-Boosted-]

Arlington? I’m from Edmonds Lived in marysville too

Yes, I am in Arlington and work in Everett.

I looked through my bucket of glove box parts this weekend but unfortunately I do not have the part you need.

Bill

 

[liznelson]

Yes, I am in Arlington and work in Everett.

I looked through my bucket of glove box parts this weekend but unfortunately I do not have the part you need.

Bill

Thank you for looking