Search results for query: *

  1. dart4forte

    Steve Magnante’s Old Valiant

    Anyone know the whereabouts of Steves Valiant. Last time I saw it was on a auction site in OZ. This is the last pic I found. Car was at an auction somewhere in OZ.
  2. dart4forte

    2007 2500 CTD Suggestions

    I have a 2007 2500 CTD 4x4. Bought it new in 2007. The issue at hand is my wife has bad knees and finds it hard to get into the truck. I have running boards which helps but she still has problems. I’m looking for a way that I can lower the front of the truck so that it’s easier for her to get...
  3. dart4forte

    Bypass hose

    Anyone have a source for the T state to water pump bypass hose for a small block? Can’t seem to find one?
  4. dart4forte

    New Years Day Run

    Did a run to Tortilla Flats this morning. Tortilla Flats is an old Pony Express stop in the foothills east of Mesa Arizona. Good turnout, no breakdowns, good people.
  5. dart4forte

    Got the Motor Almost Ready

    Little commando 273, going in my 66 Valiant.
  6. dart4forte

    Silver State Challange

    Anyone follow the Silver State Challange. Weekend before last. Bud of mine goes there to be a corner worker. There were some pretty impressive times. Nobody was killed or seriously injured. One gal wreaked her car and ended up in a Reno hospital but it appears she’s out. Several cars stood out...
  7. dart4forte

    Just a real quick question

    What year did Chrysler start using the nylon teeth on the small block timing gears?
  8. dart4forte

    Valve Cover Gaskets

    Anyone still make a thick cork gasket for stock valvecovers? After replacing the gaskets on my Commando valve cover it took about six months for them to start leaking. I used the Felpro gaskets but they were real thin.
  9. dart4forte

    Turn signal Switch

    Anyone have picture and a source for the male and female connections for the turn signal switch for a 66 A body?
  10. dart4forte

    8.75 Diminsions

    does anyone know where the chart is on the forum that show the dimensions for the 8.75 rear, pad to pad, flange to flange etc.?
  11. dart4forte

    Tanks Inc.

    Has anyone used the Tanks Inc MeterMatch to correct their fuel sender/gauge readings?
  12. dart4forte

    273 Build

    Well, finally got word that the engine builder that has my 273 got started. He called me on Friday and said the block checks out, deck is good and mag’d with no cracks. However he did have bad news. After boring to .040 he found three holes with issues. Two have fairly deep pits and the other...
  13. dart4forte

    Windage Tray Washers

    I recently purchased a windage tray along with the main bolts for my 273 build. The tray didn’t come with the washers needed for for using they tray with the 273. Does anyone have a tray they can get the measurement of the washers. I know they are thick but I can’t remember what size and...
  14. dart4forte

    Removing Piston Pins

    I need to remove the pins out of some 273 pistons. What is the tools remove the clips. I had one but I can’t seem to find it. Probably loaned it out and never got it back.
  15. dart4forte

    Transporting an engine

    Picking up my 241 Hemi next month in Washington and bringing it back to Arizona. I’d like to secure it to an engine cradle. I’m no carpenter. Anyone have any ideas on building one. It’s probably simple, I’m just overthinking this. Any help would be appreciated.
  16. dart4forte

    OZ UTE Question

    Just curious, what would it tak to put a small block into an Aussie UTE? Headers, electrical, front end K member, motor mounts etc.
  17. dart4forte

    69 Barracuda A/C Switch

    Is this switch for some type of rear A/C or is it the rear defogger?
  18. dart4forte

    66 Valiant Turn Signal Flasher location

    Anyone know the location of the turn signal flasher on a 66 Valiant with AC?
  19. dart4forte

    Torque Spec

    Anyone happen to know what the torque spec is for the 90 degree oil filter adapter?
  20. dart4forte

    Inner Axle Housing Seal

    I’ve seen on the forum off and on that with green bearings the inner seal is not needed. Seen different opinions on the subject, any ideas?
  21. dart4forte

    73 BBP Conversion 66 Valiant, Idler Arm

    Working on a 66 Valiant that the previous owner converted over to 73A body BBP. I bought a kit from PST to rebuild the front end. Ordered the 73 kit. Everything looks pretty much straight forward. Question is the idler arm. I still have the 66 K member, will it work? Hoping someone has done this...
  22. dart4forte

    O2 Sensor

    Can anyone tell me the thread size and pitch for an O2 sensor. Went back to a carb and trying to plug the O2 sensor hole on the exhaust.
  23. dart4forte

    Need Schooling on 73 Up Disk Brakes

    I have a 66 Valiant with a later A body disk brake conversion. I have the big bolt pattern on the front rotors and the 7.25 rear. was this the only disk brake setup that came on the 73s. I need to rebuild the front suspension and I have to order a front end kit and wheel bearings.
  24. dart4forte

    66 Valiant Rear Leaf Springs

    Anyone have recommendations on a rear leaf spring for a 66 Valiant? The current 5 leafs are tired. Want something for mild performance.
  25. dart4forte

    Changing A Sending Unit

    I have a inaccurate sending unit in my 66 Valient. Question I have is how low do I need to get the fuel level so I don’t have gas gushing out when I loosen the lock ring?
  26. dart4forte

    Weird Intake

    Bought this from a member and just got it yesterday. Take a look at the heat riser. Also, it is a LD4B but the 4 is missing. Doesn’t appear to be machined off. I’ve never seen one like this.
  27. dart4forte

    Lower Control Arms

    Anyone have a picture of a 64-72 lower control arms with the sway bar tabs?
  28. dart4forte

    Mounting A Tach

    Looking for some ideas on mounting a tach in my 66 Valient. I have a small Autometer tach.
  29. dart4forte

    Santa Scott

    Ho Ho Ho
  30. dart4forte

    Valient Front Airdam

    Just curious, has anyone who owns a 63-66 Valient fab an airdam for the front of their car? Saw a 66 at the Goodguys auto cross that had one. Looked a lot like a 69 Z-28 piece.
Back
Top