Search results for query: *

Anyone have any problems sealing the rear of the oil pan on a 440? I went through three different sets of gaskets two different rubber ones and one set of cork. I got a new windage tray. Oil pan got a dent in back of it during one of my 5 installs and we banged on the lips to make sure they...

Anyone having trouble with the pulleys not lining up? The belt set up has just been a mess for me. I have tried two different water pump pulleys now. The second water pump pulleys made it so alternator and water pump pulleys line up but the crank shaft is still not lines up. I would say almost a...

So this is getting annoying I cant get a plug to fit. I guess I need a 5/8 plug but only one summit has is a cooper plug. I am running a msd box and coil. Anyone know any other plug thats 5/8? I have indy ez heads. Is cooper the way to go? :/

anyone have a part number for a lokar cable that will work. Summit wont even let me search dodge for a throttle cable :banghead:

What wires are you using with out any problems? I have the schumacker headers and I dont want to order wires and not have them work.

From what I was told I have a 73 and up v8 k frame. Pic it kinds bad but is that right? I got the schumacher mounts and for some reason the drivers side mount is inch/inch and half longer. Can I just use the mounts or it there mods that need to be done to the drive way perch? From what i thought...

anyone have the part number or place to get a stock tube for a 440? Doesnt look like the milodon one I have is going to clear that splash pan that goes on before oil pan. Cant think of the proper name right now for the splash pan :oops:

Trying to get some info on this distributor. I have a 440 with flat top pistons .30 over forged crank ly robs haven't picked a cam and think ebbie heads. Car is mostly for street think this distributor would be good?

I have a 440 .30 over looking around 500hp and I want to buy a new pick up. Its a stock depth pan. What pick up would you recommend? stock? MILIDON(PARTNUMBER)?

i know i posted something a while back but now i cant find it :/ so whats the pros and cons about the two heads? i been here people are buying the edelbrocks and having to send them to machine shop to be fixed and never really hear or see anyone using the stealth heads. I am looking for a 500hp...

Ok whats a good set of piston rings to use? Looking at around 500hp .040 over srp pistons

building a 500hp 440 Where is good place to get a new blanacer? is it best to get cam, springs and lifters as package or peice it together? is closed chamber all they make for alum heads?

I started tearing my motor down and trying to see if what I have is junk or can be used. I am building a street car but I want some good hp. Also I have some surface rust on the lifters is that something that can be cleaned off? I mostly want to know if pistons are a decent one and are the...

anyone heard of them? good? bad?

Ok I am looking for some ideas. I am building a 440 and I want to change my cam set up. I am more then likely going with hughes 1.6 roller rockers unless there bad? Car is mostly for street but I want a good lumpy cam. what you think a good one is?

I am trying to see what heads I have on my car and if there the good ones or not. I only number I seen was 2408518?

Is there enough room to run heat or power steering with a 440 in duster?

Ok I think I messed up somewhere. I went to put my 440 in and and its not going in there right and wont level out. Do I have a slant 6 k member or small block k member?

Has anyone tried the heads off 440 source?

What all do I have to replace to change to roller? Anyone have a round about guess how much that cost? Is roller best way to go?

strange question but do they make a high rise intake in a single carb? if so who and where can i get it?

Has anyone tried the 440 source stroker kits? If so how much work had to be done to the black other then bore?

whats a good place that doesnt take my wallet to get a serp belt change over?

ok i put a 440 in a dart sport. the brake booster is hitting valve covers, is there a smaller one i can get?