Search results for query: *

what is the windshield washer squirter hose size?? 1/8? thanks

Delete

I bought 2 new door jamb switches (originals missing). I installed them, but the are approx 1/4” too long. Do they make shorter ones? Is it possible to shorten these? How? Thanks

I replaced my 65 Barracuda trunk lid with a 64 or 66! I thought it was 65....but it must not be. I installed my original P L Y M O U T H letters. Darn it ; the M is approx 1/8” lower in alignment than the all the others. Another words, the 2 mounting holes in the lid are lower. Any...

Goes in the trunk somewhere. Anyone have a pict where it goes. Thanks

I need clips for the rear qtr top trim and the door top edge trim. Sources??? Thanks

Just like the title says.... I need the 65 Barracuda headliner WIRE length. Its the 2 retaining wires between the top of the rear window and the last bow. I looked and cannot find a source for new ones....so I need to make them. I'm on hold til I get the numbers.... Anyone? Thanks in...

SO I watched the videos, did all the prep and marking, got all the materials on hand a prepped. Glass is even removed from the 65 Barracuda. And the famous last words on the instructions were "....with patience, an ammature can be professional results......" Yeah....right. I can't past...

seems there was a thick paper between the seat back and carpet AND floor pan and carpet in the 65 Barracuda. Its shredded. When replacing carpet did you replace it? if so with what materal? Thanks Also: need interior carpet install picts if you have them.... Mike

I also posted this in the Mopar Interior forum...but my guess is that us orphan early A guys hang out for ALL the info in just this forum. so here's the post. If you can help!!!!!!! great!!!!!!! anyone in NJ want to make a few bux and install the headliner and glass? no tear out. just...

I don’t know what I have here. The door jamb striker latch screws w tooth washer sit too proud. I think they are the right screws with cone shaped washer. When close the door, the door scrapes the screw head. What have I done wrong????

Hi. I need to buy 2 rear bow tension springs for a 65 barracuda. anyone know of a source??? Also: bow color sequence for a 65??? My old notes say: Brown, Green, Blue, Yellow, Violet (from front to rear)

I was wondering; i have a 67 B body oil pan from a 318 - - is it the same part number as the 65 early A body v8 oil pan??? sure looks like it.

I'm looking for the 20" or so, long seals that go between the A pillar and the qtr window of the front doors. What are they called? where can i get them? 65 barracuda

I only have 1 knob for the door lock pull for the 65 Barracuda. What thread is it? ....just thinking out loud, I guess I could measure it tomorrow. Anyway; does anyone have a single stock 65 one they could send my way????? cost? I don't want an aftermarket plastic one..... thanks n Mike in NJ

We (HS shop class) started with a 1965 Barracuda that was parked dead in a driveway for more than 20 yrs. Original 273 seized. The car was taken down to nothing, and is being rebuilt leaving the 'outside' 1965 finish. I've posted before about this car. Build: fixed floors, tied frame rails...

for a 65 Barracude; I got the following light bulb numbers from Rock Auto. do they seem right? Map Light (under dash) Philips 90 Ash Tray Wagner 57 Glove Box Philips 1891 Dome light: Philips 1004. What are the C pillar light bulbs??? TIA mike

I have a 904 auto and 318 in the 65 Barracuda. so the orig. cable shifter set up is useless. I have a used Mr.Gasket shifter with the twin loop/pull lockout for the R and Park - but Im missing some attachement hardware. to keep things simple, what is the recommend easiest / cleanest shifter...

Installing a 70 904 and 318 into a 65 that had a console shift cable auto trans. There is a little pushbutton in the old console wiring for the ( I assume) BU lights, Any ideas on how to hook that up to a aftermarket floor shifter? Also: the Neutral safety switch. is the 3 pin on the newer...

1965 Barracuda. How do you install the soft rubber window seals in the rear qtr windows? picts would be helpful too. Also: how do you removed the pins from the steering column connector??? I need to put the new wires from the new signal assembly into the old white connector.....so it can...

Here is the wiper switch and ignition switch wiring for my 65 Barracuda. Other than the molded plug, does anything go on the B tab on the ign. switch? Wiper switch: molded plug no problems. But the white single, and the other two singles (red and yellow)....are they on the right...

Can someone post a few pictures for me please. For a v8 65 Barracuda - no AC car. It was 4 yrs ago it was taken apart....now that I'm putting it together, parts are missing and my memory is fading.....they'd help! thanks Detail picts of alternator brackets / mounting Detail picts of...

I removed the original radiator from my 273 Barracuda. 2524961. at 318 went into the car, and its not stock. I'm going with a different radiator. The 65 would need a new core, and 1 side has de soldered itself from the tank. Anyway, Is there a market to sell it?

So as we build this car, I get the driveshaft shortened for the build. The car was apart, so I scoured threads here for a C to C number! 65 Barracuds with 904 and 8.75. I had it made 49 1/2 C to C. We installed the drivetrain, then onto the driveshaft. Nope....its doesn't fit. WTF...

Im going senile, so i need a little help here. We took apart a 273 2 years ago, and saved some of the parts to put on our 318. the 318 will go into the 65 barracuda. the 318 is from a 68, b-body i think. the 318 will also get the 273 pulleys. specific questions: 1) will the center...

ah.......screw it. Just bought the lisle 18000. one and done.....

Stock radiator for my 65 is: 2524961. Probably needs a recore, but the tanks are nice. But on hand, I already have another SB radiator - that I had boiled and leak checked a few years back. 2524961: core 17x22 OA: 22 1/4 x 26. Stock: 65 Barracuda 273 2 brl, no ac, no ps. 2898038...

Its been a while since I put a modern lever shift 904 into an early A. I seem to remember it being a little tight....above the levers to the tunnel/floor. I SEEM to remember banging a little relief (3x3 area - 1/2" up) to make more room. I can't remember for sure, and haven't found any...

For our project 65 Barracuda, I was looking for a lower fender patch, for behind the front wheels. I scored one here, at it looked to be the same, but I knew it was from a Dart. We cut the old piece off, and squared up the donor part; Low and behold, the dart fender patch was ~ 1/2"...

My school BOE came through!!!!!! I've been asking for a rottiserie.....and now they approved a purchase of one! yehaa!!! Will make the underside cleanup, welding a breeze. much easier and safer to work on. The 65 has been stalled for a little bit, as I was waiting to see if it was going to...