Recent content by 11.2

  1. 1

    Bump steer question

    I don’t know the exact alignment specs but they are somewhere in the range of Toe in - 1/8 Camber - negative 1 Caster - positive 5 I don’t know the method used setting the strut bars. My plan is to find out how to set strut bars, double check alignment and check bumpsteer again.
  2. 1

    Bump steer question

    Last season I found a crack in lca at pivot shaft. I repaired, welded k frame and new lca bushings. I’ve had the cap uppers for over ten years and 20,000 miles, so far so good but yes, plan is to change to hotchkiss. I didn’t do the alignment/ setting of the strut rods, I had a shop do...
  3. 1

    Bump steer question

    Pretty much everything. Stock k member, tubular uppers ( cap ), boxed lowers, firm feel box, 11/16 tie rods, hotchkiss strut rods. Stock spindles. I have a set of hotchkiss uppers I’m going to install eventually but I don’t think they will change bump steer without their bumpsteer kit.
  4. 1

    Bump steer question

    And FYI. the droop measurements are very similar to compression
  5. 1

    Bump steer question

    I can’t answer that at the moment. I will check tomorrow though. It’s crazy, My toe changes enough that you can see it when you put a straight edge on the rotor. It’s toed in at full compression and toed out at full droop. And the longacre gauge confirms that.
  6. 1

    Bump steer question

    I bought a longacre gauge and tried it out today. I’m either doing something wrong or I have an issue. Here’s my findings. Seems pretty basic but maybe I’m buggered up. - Passenger - Compression. .5” .055. 1”. .090...
  7. 1

    22” radiator, do they keep up

    I’m curious if the 22” rads keep up in stop and go traffic and ac on ? I currently have a 26” rad but 22” opening ( that’s what the car came with), works great but I need a new rad and would like to go to a 22”. Cutting the rad support is not an option.
  8. 1

    undercoat floor

    Robert hit the nail on the head. I actually had about 3” of water on the floor when I crossed a river last summer, I had to pull my carpet out to get everything dry. Roccodart, I’ve read about por 15 and actually have a tin of brush on and would love to use it but the surface rust I’m talking...
  9. 1

    undercoat floor

    I have a Geo tracker that is in excellent shape and I wouid like to keep it that way. I want to paint underneath the carpet, there’s some light surface rust and that’s it. I wouid like to undercoat to help with the cab noise but will this actually seal and not allow water to get trapped? I’ve...
  10. 1

    Sound deadner

    Luxury Liner Pro - Mass Loaded Vinyl + Closed Cell Foam - 1 sheet 24"x54" (9sqFt) Anyone ever use something like this?
  11. 1

    6.4 in an e body questions

    I’m starting my swap, I’m looking into tti headers. The only set they have that will work with stock k member and air conditioning say that a borgeson box is required but they don’t specify If the borgeson box is only required for a bodies or e bodies as well. Can any e body swappers chime in...
  12. 1

    6.4 going in a 74 Cuda questions

    Well I’m starting my swap, I picked up my motor today. I have a few questions to start with. -I’m getting mixed reports on the oil filter with stock k member, can anyone tell me if the stock filter works or do I need the 45 adapter? - what kind of heater hoses to use ( with 90’s )? - is there...
  13. 1

    Disassembled Stroker, what’s it worth?

    Without looking it up it roughly 250/240, 550 lift.
  14. 1

    Disassembled Stroker, what’s it worth?

    I don’t have a vin number and motor is 4 hrs away from me. As far as year goes im not sure on that either. I could find out though.
  15. 1

    West ( alberta)

    West ( alberta)
Back
Top