Recent content by flyfish

I run that same Hedman Hustler header, but in the 1 3/4 primary (I didn't know about the bigger version at the time). I like them. My old 7qt low profile milodon pan had to be massaged with a hammer to make them fit. A few years back I switched to a Canton pan that clears the headers (but it...

Haha, yeah, oddly enough if doesn't bother me when some people call me a sand bagger....it just makes me smile. There are times though that holding a few numbers and driving the stripe can win you a race that you would have normally lost if you had dialed what the car would run flat out. There...

I love driving the stripe and playing mind games (sorry to those in the other lane). My advice starts with the must haves....must have a consistent car, and you must be pretty good on the tree. With that said, I spent a lot of time collecting data on my car like: 1. If I rip it once, how much...

I only have a couple pics from picking it up (and the lighting is terrible in both, lol)….here you go.

Not sure why you can't see the pic, but its a Haul-About trailer. Got it from Trailers Midwest up in Elkhart Indiana....Just a basic enclosed trailer.

Sorry for the late reply, but yes, I see ads between every 2 posts (like what others said) + the top, right side, and bottom....over 30 on this page. I tried clearing cookies like others said, and it helped for a few seconds after reloading the page, but then the ads came flowing back in like...

Ah, gotcha. Just a suggestion (take it or leave it), if I were someone just passing through, maybe just looking, I would be VERY turned off by the sheer amount of ads thrown in my face. When I see websites like this I back out and never come back.....just saying, this might drive folks...

I have not been on here in a while (life got busy)...and this Might be a silly question, but what is up with all the ads? I know they are a source of revenue, but seriously, I'm having a hard time scrolling through just to read a few posts. The ad density is incredible. I have not see a...

I have a Canton pan on my 67 Barracuda....not a fan coming from a Milodon. I had to cut a rather large notch out of my K-frame to make it fit (passenger side front corner), and it hangs lower than my old Milodon pan. 1 positive note, it did clear my headers just fine without shaping.

Picked up my new Trailer Saturday :-). 8.5 x 24' with 5200# axels, metallic gray and screw less....now all I have to do is rebuild my engine before April to make the first race of the season, lol. I better get to work!

Lots of good info, thanks guys! For clarification, I have an old 3/4 ton duramax that I tow with. One more question, has anyone had any issue with excess heat inside of Black vs White trailers? I love the look of black (or dark blue) trailers, just not sure if it would be substantially hotter...

I have not been on here in a while...life got busy with kid stuff and I didn't race at all last year...Anyway, I'm planning on upgrading from my 18' open trailer to an enclosed trailer before racing season starts. I will be hauling my 67 Barracuda and some tools (that's about it)....Just asking...

I just noticed that you probably could not see what I wrote in the replied quote above (post#11). The 302 heads are not a good choice for this application (they don't flow well at all). I would go with an aftermarket head (lightly ported Edelbrocks or Trick Flows would work).

This engine will not get you there @ 3400 lbs. I run a 10.5 index, and like others have said you need to be able to go under the index even in hot humid weather (for example, my car will go 10.3 in 95 degree humid air). The other thing you need to look at is what kind of tree they will be...

Having had a warmed up 318 in my Barracuda when I lived in Colorado (over 20 years ago)....I can tell you that you are probably no where close to 320hp right now. If you think I'm wrong, take it to Bandimere Speedway and see what it runs.....if it runs 14's or better then I'm wrong. My guess...