Search results for query: *

You bought a Volare! The website is forfmjbodiesonly.com if you want to pick the brains of the F body experts, that is if you're not a troll, we don't like trolls at FMJ bodies. We're nice, polite, folk over there.

Is that PBR asking for directions to the nearest Walmart? :rofl:

I appreciate the suggestions. Thanks Dwayne

Hey Chris, i will PM you a list of hotels were booked in...power tour....

Captain Morgan? sure!!

Guten Morgan

this 273 has all the good stuff in the engine. 920 heads ld4b intake

Sorry !, car is a 69 Barracuda, has 318 auto, has a none oem ignition system, the system is a Pro Comp Electronics pc 7000, dist. and matching Pro Comp pc91 high output coil, there is no resister block, the coil and dist, must have full 12 volts to work. As I stated used a good known digital...

There is no trim piece there. The windshield gasket has a wide area that fits nicely into the recessed area where the screws are.

Guten tag

920 are around 67 cc, maybe a smidge less. 315,920... same closed chamber. The pistons were designed to work with them. Use a performer intake if you can't find a ld4b

This really aired on TV Not a chance in hell.

That looks like my old office chair but I didn't do that....must be the new guy that replaced me

ok A few hours ago I did a compression check most cylinders were 150-160 # 2 cyl had 50# dead cyl. so took valve cover off check valve gear looks all fine . bumped engine over.... looked thru the drain back areas in the head seen the head gasket pertruding out Buldging .. when...

No.. its an ultra rare Mexican 68 roadrunner with an 70s reskin. This car is highly sought after in this condition, and from everything we've heard it should be fully restored and placed in Barrett Jackson.

Finally someone named the Riff Master and the father of heavy metal, funk, hip hop and everything else. Iommi is the Master

Could it actually be an aspen?

Could you take, or did you, a closer picture of the Drivers Side track closest to the propeller shaft hump. I'm in need of verifying that the tracks I have are correct. Thanks.

The short of it is… yes the needle bearing I found will work it you mill the outside diameter down… especially all the way and not like me where it got stuck in the tube and I couldn’t get it back out to mill down more…. So I got pissed and took a hammer to it and collapsed the column. Go me...

I endeavored to finish the circumnavigation of the Olympic Peninsula today. It’s only 330 miles but it took me 13 years to complete. I just had the southwest bit to do really and it was a beautiful day. So my daughter and I went to the beach up at Kalaloch. I think car clubs do it in a weekend...

I got the one off eBay and already picked it up. Looks like my 70 upper housing pieces will go right on. Overall this is a better design if you as me with the bearing held by the spring in the shift tube. This was what I was trying to do with my 70 column. Long story short …. It collapsed...

Thanks everyone… found one locally.

Is there a part thar goes over the screws between the top metal of the dash and the windshield. Im looking for one for my 68 barracuda. Tried search, was not successful. Thanks.

If you all have been watching on my 273 commando engine build I have replaced the head gasket 3 times in the past two years on the pass side ... searching my posts you will the details on different topics .... So.......... I put on approx couple hundred hard miles since I installed the mr...

99 Toyota Avalon (my dd) 08 Toyota Avalon (wife's dd) 72 Duster 440 72 Chrysler Newport 400 08 Pontiac Grand Prix Gxp- for sale 01 Mustang GT vert- for sale 82 Chevy C10 shortbed 454 75 Chrysler Newport 440 parts car 73 Chrysler New Yorker 440 parts car.

I wish I knew what I wanted honestly. I have the 340 and 4 speed. I want to restore interior and everything mechanical but I love that look of the car fenders were really bad. Looked like farm equipment hit them multiple times had slices in them and bent in front. Car is cut for fender...

If the fender tag doesn't have A-57, it doesn't have the Road Runner option or, you have the wrong fender tag for the car. I don't see A-45 listed as a Volare option.

OUCH. And i in turn replied with you.

oh.. i got my pitman arm off, chisel worked.. the joint is tight but super dry and no zerk :( need to get a new arm..

The Gen 3 Hemis don't sound much better than the V6 cars when they have loud exhaust. I hear them on the interstate about a half mile from my house making noise at night. They have a distinct sound and it ain't pleasant! That was the main reason I ditched the 5.7 Hemi swap for my 70 Duster and...