Search results for query: *

Are they the same (or compatible ) to 73+ A-body calipers? They look the same in picture?

Having trouble getting spark out of my ignition. I have an MSD a high voltage coil and a stock electronic distributor. I rewired it the ignition according the MSD instructions, which eliminates the ballast. A first it ran great. I drove it for while then it no spark. I checked the wiring, and...

Need some work on a 904, anyone know someone good in the Triad area (Greensboro NC).

This it what I got for Christmas! MERRY CHRISTMAS EVERYONE! !!!.......

I have a New big block (RB) Proform conversation kit $110 shipped. (SOLD) I also have complete engine harness (plug and play ) for early A V8 that I think I bought from Harbs a while back. Used but it good condition $60 shipped.(SOLD) And 5% for paypal.

So I converted my 65 Barracuda (that had been converted to electronic) to a MSD type ignition. I bult a new harness to make it a clean installation. Car ran great but I noticed the amp gauge wasn't moving. After driving a while the car starts to stall out (turned out to be low battery voltage)...

Can someone tell which of 2 ammeter wiring going to the to firewall goes to th alternator?

I'm looking to improve the steering reponse on my 65 Barracuda. All the linkage is new and I have a new 16:1 box, but it's still slop in the steering going down the road. Firm feel sells an idler arm with bearing inserts (is this a kit you have to install or is a complete arm?) and a brace for...

So I've been having trouble getting my stock electronic ignition to run right with my new engine set up so I borrowed a friends MSD unit and it fixed all most of my issues. My question is what's the best way to wire an MSD bypassing the stock wiring harness. When I hook my friends unit I hook...

https://www.copart.com/lot/25214479

So had to pull my new motor, because the oil pan sprung a leak on the side were I did some welding on it, after starting it for the first time. I replace the oil pan with new one and took out the right angle oil filter adapter and repaced with a straight one because it didn't work well. So I...

I'll tell ya it's always something! :BangHead: I'm installing a Kevko M302 oil pan on 360 block with a windage tray. The Kevko pickup has a tab that I asumme is supposed to mount to the Main bolt? The problem is that the windage is in the way: So that's ok (I think) I'll just remove the...

So I made a homemade baffle in the stock oil pan, but it sprung a leak where I welded the plate in. So I'm going to replace the pan. It looks like if I can remove the center link I can remove the pan without removing the engine, anyone know if this is possible? I have a 65 Barracuda with a 408...

I modified a pistol grip handle to fit on a Promatic 2 shifter, but I'm having trouble putting it back together. The main pin (the one that fits in the slot ) won't go in far enough to allow the snap ring to go on. It's sticking out and won't slide in all the way in! Tried tapping and rotating...

Hey all, tried the search thing and there's just too much to go through. I currently have a 73 manual disc setup on my 65 Barracuda. The car stops great but it has a rock hard petal and I'd like to soften it up a bit. I have 2 questions: 1st is there a difference in master cylinder force (piston...

Ok before you contact me: I've gotten comments about a couple of things I sold yesturday making claims that they asked me first and I should hold this for them. I'm sorry I don't sell for a living I'm just getting rid of some of the stuff from my garage that I don't need and I'm selling at a...

$20 you pay shipping

I have a full suspension kit ball joints, tie rod ends. Yes they are made in China, but there pretty well made! $60 and you pay the ride. Add 5% for paypal.

Need a stock pinion snubber

I have 2 brand new high volume oil pumps made in the USA! $60 each plus shipping.

Hey all, anyone the NC Traid area have a flywheel I can use to test run my motor? It doesn't have to be in good shape, it just has to have a good ring gear. The motor is on an engine stand and I need it to use the starter. It's going in a automatic so need a flywheel otherwise.

I have a 73 disc brake conversation on my 65. The brakes are un-boosted. The question I have the pedal feel is really hard and I wondering if there is a difference with master cylinder for power vs mannual set up?

I'm getting ready to start up my new engine on a test stand. I have an old stock ecu and harness to test it with. Would it be ok to skip using the ballast resistor for the short period it will take to do this? I'll probably end up using one, but I'm just curious.

Does anyone know the orientation of these bushings between the valve spring and the head? Just checking myself and want to be sure.

I'm installing a roller-cam in my LA with with 1:6 adjustable rockers and I need a set of 5/16 pushrods 6.50" long with a cup on one end. I really don't want to have to go through the expense of a custom set if I can help it.

My engine gasket set doesn't have an oil pump gasket. My new oil pump came with one but I've lost it. My question is do you need it?

I have read about using Magnum tensioner on a LA block, but when came time for me to install the timing chain on my new motor it's hard to see this tensioner would work? If you look at the tensioner arm to the right of the photo it needs to move over about an inch to the right to the other...

Looks like someone is reproducing these boxes. New Quick Ratio Manual Steering Gear Box Fits Dodge Chrysler Plymouth Mopar | eBay New Manual Steering Gear Box Fits Dodge Chrysler Plymouth Mopar | eBay And noticed it looks like PST is selling them as well. Anyone buy one of these? If so can...

I'll be selling some early A stuff along with carbs and engine stuff. Come by and say hey! Matt