Search results for query: *

Right hand turn signal stopped working and was affecting the brake lights. This is only a couple of years old and there's already a bunch of brass shavings from the horn roller. But I digress. Separated the turn signal and looks like the contacts where deformed. I'm presuming these go around...

Is this indicative of a bade voltage regulator?

Is there supposed to be something that seals the column inside the engine bay? The fan is blowing hot air up the shaft into the cabin. It looks like there's holes for something to mount, but I'm not sure what that should be.

Car idles fine and cruises fine, but pings when accelerating. I suspect timing. It's a 1973 225ci Slant 6 with a Carter BBD 2 barrel carb in a 1964 Barracuda. It has an electronic ignition installed, not sure if that makes any difference. I'm not trusting my timing light. It's one of those...

I need to remove my quarter window trim and in order to do so, the felt needs to come out so I can access the screws. Is there a trick to this? I'm trying to keep from bending anything and breaking (any more) tabs, but it seems counter intuitive. Looks easy to pop in, but kinda a pain to get out.

I have them, but not sure where they are supposed to go on my 64 Barracuda. Does anybody have any reference pics? https://www.detroitmuscletechnologies.com/mopar-63-66-a-body-and-62-65-b-body-frame-torsion-bar-splash-shields/

My cylinder assembly freely pulls out of the ignition switch regardless of what position it's in. The pin seems fine on the cylinder, but it looks like the switch is damaged where the pin is supposed to seat.

I found there is a pinhole at the back end of my drip rail that allows water to leak into my quarter panel behind the quarter glass on my 64 Barracuda. It leaks like crazy, but it got me thinking, where are the weep holes supposed to be for the quarter windows? My panels were repaired before I...

I drove to school to pick up my daughter and turned off the car. Daughter hopped in and I turned the key. Started for literally a second and then nada, like dead. No lights, no nothing. I got my daughter taken care of and started troubleshooting in the school parking lot. Last thing I did...

The speedo never worked in this car when I bought it. I've finally starting messing with it and I don't know if it's bored out or if the cable just isn't the right one. I thought it should be square, but this one looks circular.

Our car didn't come with any splash shields, so I bought those from helpful folks here on the forum. I bought the gasket set from Detroit Muscle, but I'm not sure how they install. I mean, I do, it's kinda obvious, but kinda not. Since I have no reference it's hard to determine. I presume I...

So, I've been working on the 1964 Barracuda. I replaced the clips in the fuse box and wired it up the way it came out. Today, I noticed that one of the 20A fuses was blowing. The fuse is supposed to be for the cigar lighter, but it's not hooked up. It was a yellow wire. I confirmed with...

I've been having a hard time finding a switch. I've bought two different part numbers that indicate they are compatible with my 64 Barracuda, but they are too long. If I close the door all the way, they will be crushed. Left is original, middle is Standard Motor Products DS173T and right is a...

Looking for a foot pump for a 64 Barracuda. Doesn't need to be functional as I'm going to modify it with a switch to use a powered pump, but it'd be nice if it were cosmetically sound.

I've been looking all over. I can't manage to find a wiper refill. Everybody wants to sell you the blades, but no refills. My blades are fine and don't need to toss them in the trash to spend money for something I don't need. I checked the service manual and can't find a part number there...

I bought this kit from Detroit Muscle Technologies. https://www.detroitmuscletechnologies.com/mopar-a-body-64-66-barracuda-dart-valiant-body-bumper-set-bbk12a/ Unfortunately, it doesn't come with any instructions on where what goes. I've identified some parts, but others I can't tell where...

The Barracuda I'm working on has the radio, but nothing else. No speaker or mounting hardware. From what I've found on the forum, I'm going to need several pieces. The dash speaker mounting frame, some elevator bolts to mount the frame to the dash, a 6x9 speaker, but I'm not sure how to mount...

Sorry for the ignorant question, but I just replaced the cap, rotor and cables on my distributor and wired it up per the firing order. Can't get the engine to fire, and then it dawned on me, I don't know which way the distributor rotates. Clockwise or counter-clockwise on a slant 6?

Had to pull my distributor to replace the vacuum advance. When I pulled it off, it had what looks to be a home made gasket. I checked the manual and I'm only seeing an o-ring. Is it supposed to have a gasket between the block and distributor?

I bought a 1964 Valiant service manual off Facebook. I know there are scanned versions, but I've always had better luck with the book at the car while working on it, but I digress. Thumbing through the pages, I come across this piece of paper folded up and inserted into a plastic bag. Thought...

Is there a chart or matrix of what switches are compatible with what vehicles? Currently our 64 Barracuda has a single speed wiper switch (part number 2291668), with no windshield washer equipment at all. No nozzles, lines, reservoir or pump. I'd like to replace my switch with one that...

So, I was messing around the 64 Barracuda's trunk and noticed the license plate light was just a single bulb with no guard. I guess what had actually happened is a previous owner just got a light socket and glued it into the hole that originally had the wire and grommet for the original license...

I pulled an electric trunk release from the local LKQ and I'm installing it in my 64 Barracuda. I've searched, but could only find topics where people are asking for them and not much about installing them. Those who have installed this, did you fuse it? If so, what size fuse did you use?

Anybody have a source for these? I pulled my fuse box because they were all rusted up. After dumping a bunch of stuff in my face because the box didn't have a cover, I cleaned them up. I can definitely still use these, but wasn't sure how quickly they would rust over again since the plating...

Hello all. I'm looking for some parts for our 64 Barracuda. Armrests for both front and back driver and passenger sides. Would prefer black. Kinda hard to shut the door without them with the windows rolled up. ^_^ Window cranks for quarter glass. Glove box insert. - Found Kick panels...

These parts came with the our 64 Barracuda, but I'm not sure where they belong or if they even belong on the car at all since it doesn't have the Chrysler emblem on it. They are plastic, so I'm presuming they are some kind of interior pieces. I tried to search the part number, but nothing came...

I was wondering if I could repair this emblem or if I should just get a another one. It was already damaged where the nipple on the back was broken and it was glued down by the previous owner, but when I was walking past the car, my shirt snagged the edge of the emblem and snapped it in half...

One of my front running/blinker lights wasn't working on our 1964 Barracuda. Was going to check the bulb but it ended up being rusted in the socket. Had to bust the bulb and use a pair of pliers to twist the base out. Ended up looking like chewing gum by the time if fell out, but I digress...

Hello all. I'm in the process of installing the Sebring seats into our 1964 Barracuda. I'm working on the wiring now, but I have an extra wire that is not discussed here. It's one of the 4 wires that are bundled that go under the drivers seat not including the power seat mechanism. Below are...

I've been trying to find a replacement fuel filler tube but haven't had any luck. Rockauto seems to have everything but that. Currently it has a makeshift filler tube made of small diameter hose and adapters on each end causing the fuel to backup and spill out while you try to do gas it up.