Search results for query: *

So i have been doing alot of reading on here and i think my cam is way to big for the converter i have. I have the eddy rpm cam. Many of you have said that you dont like that cam and i am just curious. I have a 3000 stall 904 with a reverse manual valve body. 3:91 in the rear. Could the cam be...

I am in the market for an adjustable timing light and found this one on Amazon. Seems like a good deal. Amazon.com: Equus 5568 Pro-Timing Light with Tool Case: Automotive@@AMEPARAM@@http://ecx.images-amazon.com/images/I/41cxTsn9U1L.@@AMEPARAM@@41cxTsn9U1L Has anyone had any dealings with this...

So i went to start my jeep this morning and it cranked over buy nothing happened. It came up with a message "no bu5" on my odometer. Anyone have any experience with this?

So i have recently discovered that my k frame in my 74 dart is the earlier style with the biscut style motor mounts. So my question is what do i need to do the swap. Do i need new lower control arms? or do i just need to buy the spindle, rotors, calipers, proportioning vavle and misc. pads and...

I am looking for 74 dart style tail light lenses in good condition. Also could use the bezel that goes around the rear that holds the taillights.

So yesterday on my way home from the garage some kid rammed his bike into the side of my cherokee and dented the **** out of my passenger side door. When i got out to see if he was ok i asked him to wait a minute while i called the police and the kid took off. Im only 25 but if i did that when i...

So i have searched all over for this on FABO and havent found it so im going to ask. I have a 360, .030 over, eddy cam, eddy 750 carb, msd ignition, coil, and billet distributer. The distributer doesnt have a vacuum advance on it. So when i go to check the timing do i need to cap anything? when...

So i have finally almost gotten done with putting my new gauges in the dart and when i fired it up today my new electric gauges dont work. I bought autometer guages and i hooked the green sender wire to the sender that was provided. Is there supposed to be a wire clip or something? please help.

I am cleaning up the suspension on the dart here in the next few weeks and want to put new springs on the back. They look pretty nasty and i want to clean them up. Where can i get a set of nice ss springs for cheap. I just ordered competition engineering adjustable shocks for all the way around...

So i started re doing my interior the other day and took everything out of it. I have a 904 with a reverse manual valve body that i needed to take the shifter off to get the carpet out. When i was cleaning up for the night i was going to push the car back in so i put the shifter together and put...

So today i put my new radiator in, changed the oil and put in some royal purple, changed the filter, tinkered with the timing. After all that i went to go do a big smokey burnout and realized that only one tire was spinning. When i bought the care i was told it had a sure grip in it. Surely this...

I am going to update my alternator and was wandering which alternator i can use. I am going to bypass the ammeter the mad electric way this weekend and want to know what the best option is for alternator so i dont have my turn signals going on and off every two minutes when i drive at night...

What have you guys been doing with the extra wires that go to the mopar stock boxes after you put an MSD or similar ignition it? can i just cut the ends off and terminate them? i dont know if anyone has some suggestions or if im heading in the right direction.

Can i run 1.6 ratio roller rockers on stock heads. My lift is .510.

So i put my MSD ignition in last night, (distributer, coil, and 6al) Night and day difference over the mopar electronic ignition. I either had something messed up before and did it right or this ignition is great. Fires up instantly. Thanks for all the help from everyone on here.

So I am hooking up my MSD and Billet distributer this afternoon when i get off work but i have a few things i want to clean up before i put it in. When i bought the car the original turn key ignition was removed. So the guy put a cheesy switch under the dash. I still have to put the key in and...

Is there anyway i can acheive some of the characteristics of the alterkation front end without going with the alterkation. Like coilovers and such....

So it apears that my dart has a 70 to 72 k frame in it? If i want to do disc brakes which setup do i use?

Looking for a MSD 6al and a billet distributer for my 360. Thanks.

So i just posted the eddy heads vs. ported j's the other day and was wanting to know a little more about the magnum head swap and if that is maybe a good combo to go with. I dont want to annoy anyone by constantly posting about heads just trying to figure out what route i want to go. I dont know...

Looking for a set of small block 360 eddy heads

I am looking for a roller valve train for my 360

So i ordered a set of proform roller rockers from jegs today. I have a 360, what will i need to complete the install?

So i want to do new heads for my 360 and have been talking about it for a while and hav e chance to get a set of J cast heads for 100 dollars. Would it be better to get some eddy heads or port and polish and clean up the old J cast head. Im looking for performance vs. price here. Thanks in advance.

So im getting alot of clicking from my vavle train after installing my cam a year ago. Do you think it is because i didnt uprage the valve springs? could this cause a loss in performance? here are the specs on the cam. I am looking to figure out what springs i need and if i can just change the...

So last time when i rebuilt the engine I just threw in some 10w30, I was thinking about putting synthetic oil in it. Anyone run this and what type of oil would anyone suggest. Its a 360 with a mild cam, headers, KB 10:1 pistons, eddy intake, 750 CFM carb. anyways im replacing the radiator and...

Hi, i am looking at switching out the heads on my 360. This my current set up -360 30 over -KB 10:1 pistons -headers -750 edelbrock performer carb -edelbrock performer rpm cam with the following specs Duration Advertised308° Intake/318° ExhaustDuration @ .050''234° Intake/244° ExhaustLift @...