Search results for query: *

Okay, picked these up from another member here to use in my 4 door, but ended up getting the factory seats redone instead. Black vinyl and and heavy velour. The installed materials does not look factory at all, but is in pretty good shape and is pretty sturdy. Seats have head rests that look...

**Oops - set it to for trade, but this stuff is for sale - or trade for an electronic trunk release from a diplomat :) Cleaning out the parts bin! From Detroit Muscle Tech - remainder of my 1972 Dart paint gasket kit. $25 for the rest of the kit - here is what is left over: Door handle...

Okay guys - cleaning out the parts bin to make room for more stuff. 2 Coverking Carpet dash covers - $20 each SiriusXM satellite radio XM XDNX1V1 Onyx by Audiovox Dock and Play kit, with car mount, power adapter, 1.5mm connection, magnetic antenna with 22 foot lead, and all instruction...

Okay guys - I have 2 of the Coverking Dash mats for a 1970-1976 A body. One in black, one in tan. Both were used less than 6 months each, and never sat for extended time in direct sunlight - a hard feat in AZ. These are not the molded dash caps or pads, but a carpet protector to protect your...

Okay guys - wife said the chrome trim from the Brick had to go, so I pulled it off. Nice, driver quality. Minimal rust around the mounting holes. - Hood and the surrounds for the headlights - includes all mounting screws. Would prefer that they all go together, but will split hood trim from...

I know, I know, you guys see this question all the time, but I have a few questions about installing a high amp alternator in the Brick. :banghead: In the very near future (hopefully this coming weekend) I will be adding 2 audio amplifiers to the Brick. Current plan, because of lack of amperage...

So, in working on the Brick, I have found myself being about 80% done with the interior. Currently running a set of black velour and vinyl seats from a 2 door Hardtop that I got off a member a while ago - I still have the orginal seats, but want them to more closely match the interior as it...

I have 2 Coverking Dash covers that will fit any A Body from 1970 to 1976 (not sure about the 68 or 69 Cuda, or earlier A Bodies). One is tan, and was used for about a month, the other is black, and was used for a year. Neither show any wear and tear or sun fading. Never attached with the...

So finished my rear end swap. 3.23s in an 8.25 - Running BFGoodrich Radial T/A - P205/70R14 25 inch tire. Found in this thread: http://www.forabodiesonly.com/mopar/showthread.php?t=133767&highlight=speedometer I need a 34 tooth speedo drive gear to get the speedo back to close to right...

So does anyone have pics of the rear seat belt setup for a 2 dr Dart Swinger? I swapped a set of seats into my 4 door from a 2 door and am curious as to how the rear seat belt retractor assemblies look and how they are arranged. I am fabricating some lifting brackets for the rear seat, but I am...

Okay guys, this Sunday, Gene and I will be starting to take apart a 1965 Cuda 273 4 speed car. From what I have seen the body is all there, except the 4 speed tunnel. Southwest car so pretty rust free, and I didnt see any down there the last time I was rolling around under it. As far as I can...

Okay, looking for the actual light buckets for a 1972 Dart. Don't need the lenses, but if they are nice, or you can't split the sets, then I am interested. Need driver quality needed, just going on the back of the Brick. Also looking for sets of the small round side marker lights from the...

So now that I am almost done with the steering and suspension rebuild on the Brick, was thinking of dropping the pump pressure to the power steering pump to provide a firmer feel to the steering. Shooting for 850ish PSI. I am going to be using the shim kit from Summit...

So any hints to getting the Strut Rod Roll pins out? Tried tapping with a hammer - no budge, tried pulling with a pair of vice-grips - no budge. Just soaked them down with pb blaster and will be back at it tomorrow with a soft blow and a brass drift.

Perfect holiday memory tonight. Was heading to AutoZone to order the parts I need to wrap up the front end of the Dart. Nancy, my 5 year old, asked where we were going, and I responded to the Car Parts Store. She said, "but Daddy, your parts are in the trunk." My wife was dimed out by my...

Okay, so I have a functional AM radio (original) in my dart and want to get a DIN sized radio into the car. I am going to be doing some stuff to the dash, and have the perfect guy to call to cut the dash. So should I do it? I know this is more of a personal preferences, but I have seen plenty...

So need to know what to look out for when removing the AC vent setup on my Darts factory under dash vents Okay, so the plan is to remove the dash ashtray from the car and fill the spot with a water temp / oil pressure gauge set. I did this on my 71 Duster and they looked good there. Only...

So I just finished installing some Mopar Superstock Springs on my Dart and I was miffed that the passenger side sits so much lower than drivers side. I verified before mounting them that I had them going in the right way (sides).....What am I doing wrong or missing here? I know the front sits...

6/6/10 The project starts. Okay so the goal here is to build a classic daily driver for less than $5000. Here is what has been spent so far: The car - $1200 Body and primer - $250 Replace trans pan gasket - $50 Total - $1500 Ordered parts: Fuel Sender unit -...

So gathering my parts for the disc brake swap on my 72 Dart and I have a question about the prop valve. I grabbed one with the knuckles, calipers, etc, that is setup for power brakes. I am not going to power brakes but I am swapping the master to a manual disc master cylinder. All the online...

Long time troll, first time member :) Well, this year marks my return to A Body life after a 12 year hiatus. Needed a second car and found an awesome 72 Dart Custom survivor dirt cheap so picked it up. I keep a little blog going through what I am doing to it and to help track what i am...