Search results for query: *

I just checked and apparently I sold it at Carlisle this past summer, sorry....

I believe I have a new center link from my 66 Barracuda, suspension I rebuilt years ago, drive the car about 10-15 miles, garaged the car and completely stripped the car. I decided to put in a RMS complete front end suspension/K-Frame. I’ll have to check to make sure u still have it. Any other...

I have RMS Alterkation with 13" - 6 piston Wilwoods I installed on my 66 Barracuda and want to sell. It's brand new, just installed to mock-up the back half. I'm changing directions and going with a Strut front. Let me know if you're interested.

Bought a new Alterkation with 13" - 6 piston Wilwoods and installed but have changed direction, Going with a Strut front end. Car is still in fabrication, the front end has never been used other than a install to mock-up the back half. $5,ooo plus shipping.

Have you bought the RMS Alterkation yet? If not I have one, brand new I bought for my 66 Barracuda with 13" - 6 piston Wilwoods and am thinking about selling because I'm considering going with a strut front end.

I have a fresh set of Brodix aluminum small block heads with 2.08 intakes that flows 305. These are ready to bolt on, just add your springs. All work was done by Ryan Johnson of Shady Dell Speed. Asking $2,200

I have a fresh pair of Bodix B1-BA heads ported by Shady Dell with 2.08 intakes flowing 305.9 at .600 lift, 60.5cc chambers. Also have an excellent set of Hughes 1.6 aluminum roller rockers. This set up is ready to go. All you need to do is add your springs. Ran an alcohol R3 block at 2800lbs in...

I have a pair of fresh Brodix B1-BA aluminum heads, stage 3 ported by Shady Dell with 2.08 intake 1.60 exhaust. Surfaced with 60.5cc chambers, Viton seals... Flows 305.9 intake 199.3 exhaust at .600 lift. All you need is the springs that match your cam. $2,200 plus shipping Also have Hughes...

Starting my project and am looking for information. Has anyone installed a Gen III in an early A Body? If so, what are the challenges? I understand the block length (including timing covers is almost identcle to an LA Small Block at 24", but what about the width at the valve covers. I'm planning...

Is this Block still available, or has it been sold?

Hey, never heard back from you... Is the inner fender still available?

What are you asking for the assented door and is it complete or just the shell?

Looking for right side NOS door skin.

Looking for Quarter Panels both left and right sides with Trunk Extensions. Not interested in rotted panels with big holes, surface rust is okay.

Is the inner fender still available, drivers side correct?

Is the left side inner fender still available?

Is the Rocker Panel still available?

Hemirunner - Is this still available...?

ebigga67 - I had talked with the guy on racingjunk.com last week and that block was sold. Thanks....!

Wanted, R3 Block Siamese 59 degree... Please let me know if you have one for sale or know someone that may consider selling.

I may be interested depending on what the Machine Shop says. But I would only be interested in the block with the main caps and your asking pricing is way too high... I would like to speak directly to the Machine Shop if you would give me their phone number and who I should ask for along with...

This is a water block, correct...? I'm interested in a Siamese block that can be bored to 4.220....

What is the specific mopar block part number and what condition is the block in?

Please advise if these heads are still available, thank you.

What is the Mopar Performance P/N...? Thanks, Russ

Wanted: B-Engine aluminum dual plane intake manifold, prefer Edelbrock Performer RPM will entertain equivalent manufacturer.

Hello, do you have any additional background information on the engine build such as specifications on the compression ratio and piston manufacturer, the camshaft specifications and manufacturer, same with the rods, bore & stroke, etc. I live in White Marsh, Maryland (East side of the Baltimore...