Search results for query: *

Hey guys just wondering if I will have an issue with swapping in 67 318 to a 68 904? I read that to swap a later engine to 67-pre 904 the converter has to of a 67 variety. Just wondering about the earlier engine to later trans? Thank you.

Hello all. Just wondering what is the best camshaft for a 68 Coronet with 67 318 (Weiand 8007 Intake/Edelbrock 600 cfm carb/Summit Headers 2.5" dual exhaust stock 920 casting heads (new stock/springs guides/seals) and stock pistons. Transmission is a 904 with a 11" PTC 2200 stall low gearset and...

Hey guys was offered a 67 318 and was wondering what the static compression might be for an engine. It is my understanding that I think all 67 318s got the close chambered heads correct? I was thinking in the neighborhood of 8.5.1 to 8.8.1 maybe?

Just wondering if you wife is happy or displeased that your into your old Mopars and the time and money sometimes we spend on them?

I'm looking for a good used running rebuilt 318 or 360 LA engine. I would prefer one that doesn't smoke and has good compression & oil pressure. On the 318 I would prefer one that has at least 9:0:1 compression. I would need proof the piston in regards to the 318 subject. Can be a rebuilt one as...

Hello, just wondering if anyone lives near East Peoria, IL. I may need someone to check out something for me since thus far because of my work/personal schedule plus trying to fly under the radar with the wife. PM or email me if you want. Thank you in advance.

Hello guys, just wondering if I could use a 68 318 waterpump and fan/crank pulley on a 73 318 engine without any issues. The 68 318 is non-AC and no power steering btw. Thank you.

Just wondering if there is much difference in using a low gear 904 vs a non-low gear 904? I'm talking about from a performance standpoint. Please let me know. Thank you.

De

Just wondering if a stock 904 would be fine behind say a 318 with 9:1 or 9.5.1 compression 256/262 voodoo cam performer intake, and 600 edelbrock carb with summit headers or a 5.2 magnum with a air gap, same carburetor, and same headers. I figure both engines are right around 300hp and 350...

At this time I don't have a way to ship it but, I have a complete 400 2bbl/727 combo from a 74 Newport that I was told that was running/driving setup. The engine is complete from carb to pan minus the fan blade/clutch. The engine also has the air conditioner/pullies and the power steering pump...

So, I'm having a brain fart at the moment and was just thinking about if I find a 5.2 Magnum cheaper than a 5.9 Magnum cheaper and closer than I am wondering what the power output would be with a 4bbl air gap intake and headers. We know the 5.9 is around 319hp and 424 I think in torque with...

Looking to buy a nice 5.9 Magnum engine. I am located near Indianapolis, IN. Let me know what you got by PMing here or emailing me to [email protected] Thanks again.

Posted a thread on the FBBO forum and haven't gotten much response. Just curious if there is much difference in say a 73 440 vs a 74 400 4bbl motor? This a no budget (Joe Mudd) project and wondering if the performance will be the same if I keep stock internals and HP Manifolds? I might go...

I have a 9811 Thermoquad F/S I bought from Demonsizzler last fall and only bolt it up once to my car but, never drove with it and maybe idled 2 minutes with it and my primary reason for selling is because I am converting to big block and will need a bigger carburetor so I don't need it anymore...

Just got a question for you guys. Where is your volt gauge reading at idle? Mine seems to be slightly under half but, my charging system is reading 13.9 to 14.0 volts at the battery posts. When I turn on my headlights though the gauges drops more I have already replaced the battery, alternator...

Hey guys, I have another item up for sale. I am selling my Weiand 8007 intake that came off my 318. There is nothing wrong with it I am aware of other than a hood clearance issue 68 B-Body with a flat hood. I am looking for $100 plus the ride. It will accept a Thermoquad because it is a...

I am looking to sale my MP valve covers off of my 318. No issues that I know and in good shape. The breather cap and oil fill cap come with the valve covers. $75 plus shipping.

I took these off of our exhaust system and just wanted something different. The stuff on them is just oil so I'm just showing them as is so it doesn't look like I'm hiding anything. $25 plus the ride for both mufflers. Here is the album to the mufflers...

I have 4 slot mags I would like to sell. They are pretty good condition with some imperfections which I think could be easily corrected. They are unilugs and they were on a 68 Coronet. I can include the washers, lugs, and centers caps I have. The washers are for a 5x4.5 bolt pattern and the caps...

I have EH1 360 shortblock out of LRE truck. I have the bare junk heads to prove it. It had 134k miles when I pulled it to replace it with a 5.9 Magnum and this engine was still running just the heads were cracked. I will include the junk heads which are bare castings. They were cracked between...