Search results for query: *

I've been driveing my car around town a bit, it's not totally done but fun to cruise anyway. My car does'nt have the rubber seal kit in it yet but does have the hood cowl seal, when I drive the car it smells like gas. I ran my exhaust all the way to the back hopeing this would solve the problem...

I switched from a automatic 904 in my 68 dart, to a abody a833 4 speed. I got it all back together, except I have'nt hooked up the wire to the reverse lights yet. My problem is it won't start now, do I need to hook up the single wire neutral safty wire that was on the 904. I did'nt think a 4...

I had a automatic 904, and switched to a 4 speed. My question is, the reverse switch on the 4 speed has a 2 prong on it, and the automatic I had had a one wire hook up. What do I need to do? Do I need to just ground one side of the 2 prong plug?

My first 4 speed install, have it all in but when I push in the clutch pedal the diaphram on the pressure plate does'nt come back out? I installed the clutch with the tag that says flywheel side towards the flywheel. When the bolts are loose on the pressure plate the diaphram releases and...

I know this sounds dumb but, I am trying to install the rod from clutch pedal to zbar, I got the kit from brewers with the clips for the clutch rod but I am not sure how they go on. The hole is offset from one side to the other so if you look directly at it u see part of the other side of the...

Is there special bolts that hold the pressure plate to the flywheel that have a shoulder or something that bottoms them out when torqued? Or some kind of spacer between the pressure plate and flywheel. I am converting my dart to a four speed and trying to install a mcleod clutch and pressure...

Does anyone know, which pilot bearing I will need for a 4 inch scat crank. I ordered the ram brass bushing from summit and it's to small. I think I am going to have to use a bearing type that goes where the converter used to sit. I'm hoping for a part number if anyone has ordered one of these. I...

I don't know if anyone else has had this problem. I ordered a set of light benzels for a 68 dart back in January, they say to allow 1 to 4 weeks for delivery. I called them after 5 weeks and they told me scheduled next week. Well next week they still did'nt show, so I called them again. Now this...

So I've been driveing my dart a little bit not much, at idle it will not over heat sitting in the driveway, but when I take it out, for a spin it gets hot and over heats. It never had any problems before I put a 4 inch stroker kit in it. It still has the original radiator the car came out with...

I've went through alot of these posts and have'nt found all the answers I was looking for, so I will try a new post, sorry for all the questions in advance, first time swapping to a 4 speed. I just got a 4 speed conversion kit off of ebay, comes with bellhousing,fork,zbar,clutch and brake...

I was going to ask about tci transmissions but after reading the third post down I won't bother. I am in the market for a new 904 and was wondering if buying one from jegs or summit is a good move. I was looking at the tci streetfighter but maybe not, after what I read in the post. How about PA...

Has anyone here built a nice hp 318 engine. You always read magazines that claim big numbers on the 318 I am just wondering if anyone has came close to these numbers with a teen. Don't get me wrong, I am a fan of the 318 I am just wondering if anyone has actually built one that has the hp these...

I ported and gasket matched a set of 318 heads that I had the larger 1.88 intake and 1.60 ex valves put in. I realize these may not be the best heads for a stroker engine, but I was wondering if anyone knows there power potential. The engine is bored .40 with a 4 inch scat crank, rods, and...