Search results for query: *

as stated,speedo cable or info as to what kind of vehicle would fit that i could get from an auto parts store?

HELLO,I NEED THE PIECES THAT STOP THE TIRE FROM SPLASHING WATER INTO THE DOOR JAMB AREA( INNER FENDER SPLAsh shields) and disc brake spindles 1973 swinger.

in need of 440 emblems,a stick on may be preferable,as my 73 dart swinger didn't come with a 440 so it won't be made to fit anyway but i'll make them fit,show me what you have.

legendary interiors is advertising a replacement plastic headliner,it appears you can get it with a foam backed material,but will cost about 300.00 plus 65 shipping,but it is not theirs and they say they have had some complaints on fitment,does anyone have any experience with these or know of...

tryed to put a rack +pinion in a 73 dart,had drum brakes,installed spindles and rotor set up out of a volare,the tie rod is sitting level just like the control arm,but when i move the car and turn the wheels it pulls the suspension down to where the l.c.a. and tie rod now are pointing up...

sold the torsion bars ,don't know how to mark as sold or delete the ad?

does it matter which end goes in first ,the numbers on the end of torsion bar facing out at the end of crossmember? and is left considered sitting in the drivers seat,meaning drivers side is the left?

hello,just put a set of poly u.c.a. bushings,stock rubber l.c.a. bushings,poly strut arm bushings in my 73 dart,now when i adjust torsion bars to a ride height where the fender is above the top of the tire,if i back out of my garage and over a bump the car lowers itself way down,if i jack the...

ad in mechanical parts for sale.

1.030 p.s.t. torsion bars.installed but not used ,as the ride height was too low for my size tires,150.00 dollars plus shipping. please respond by private message,for my phone# or e-mail address,or just a reply.thanks

looking for a driveshaft 50" center of u-joint cap to center of other u-joint cap for a dart swinger,yoke not nessasary,but using a 727 trans. please send p.m. if you can ship to 32305,florida,with a price. thanks martin

as ad says,need a valance 73 dart, please p.m. me with any leads.thanks martin

whats a fairly easy swap,taking parts from what vehicles to put in a 73 dart swinger,v8,manual trans.thanks martin.please send a p.m. thanks.

any fairly easy,complete v8,stick,from what vehicles?please p.m me with any help,thanks martin

please pm me if you have.

have a 1975 440,with a cast crank i believe.and need a manual flywheel

currently have a 4-speed but would like to go to an overdrive,looking for used o.d and cluster gears,or a whole trans,also looking for a 440 manual flywheel,motor is a late model 1975,cast crank i think.

how much with shipping to 32305 florida

also looking for fenders

need a front bumper and or a rear valance for a 1973 dodge dart.

i have a 1975 440 automatic motor,no pilot hole in crank,would like use a manual transmission,can it be done without disassembling motor.motor is out of car.is there a flywheel with a pilot bearing in it? any suggestions?

does anyone remember these,fairbanks used to make and sell kits where as you cut off bellhousing,bolted on a scattershield and used a clutch in place of converter,i used their kit on a turbo 400 wasn,t to complicated, i spoke to fairbanks and they are new owners and don,t have any literature or...

thats the question,can i put a different front bumper on my 73 dart,the indentations in my fenders look alike,i think.can i get away with bumper and brackets and valance,and th piece below the grill

#2843992 or 2951865 exhaust manifold needed

going from p.s. to manual ,picked up an early small sector shaft box,but pitman arm faces up ,my power box faces down and its sector shaft is larger, and i can't swap them because they are different sizes,is there one for the small shaft box facing down,does anyone have one? this is a 1973...

any info on a 5 speed manual for a 440

looking for a dropped center link 440 dart,also 73 dart bumper

need info on going from a 1973 style dart grill and bumper to an earlier style .the 73 has a shorter hood and something that runs across from fender to fender,and the bumper is too bulky and sticks out to far in my opinion,i like the earlier style small bumper with valance ,and dont know which...

just starting on this project,need some pointers about exhaust manifolds,mounts, and i have a six cylinder k- frame in it ,can i use it ?please respond to marty at [email protected]. also want to use earlier gill and bumper,hood from a 70,71,72.and are interested in purchasing...