Search results for query: *

I have for sale an extra NOS R & L tail light lenses with the little gasket's that are in excellent condition. $200 plus any fees and shipping.

I have for save an extra 1965 only A-body 4 speed floor shifter bezel. It's in really good shape no pits or cracks. It is not a re-production. I'm asking $225 + any shipping or fees. Thank you.

I have a nice un butchered D4B Edelbrock intake for sale. a good friend of mine had & didn't understand why it wouldn't bolt on his 360 at all. I explained to him the its for 64-65 bolt pattern only! Soo now its up for sale. it has one helicoil in the thermostat bolt hole. other then that good...

Complete Running 340 Here is a link to my 340 in my dart that I'm selling complete carb to oil pan & the custom built torque converter that's matched to it. id also throw in the spool mount K-member as well for the asking price. only parts I'm keeping is starter, fan & air cleaner. $4000...

Hey fellas, a while back I swear I had found a company that would modify your stock a833 side cover. They bored it and instead of using the single O-ring to seal the gear oil in I thought it was bored for a better lip seal. Also though they installed needle bearings for more support. Ive seen a...

has anyone ever done this at all? Iv'e got a set of used mopar SS springs off a good friends dart they were sagging a little bit. His car gained about an inch to inch & a half after the new SS springs were installed. Thought about re-arcing them & installing them on my dart as a little cheaper...

Just as the title says im getting fuel in my vacuum advance canister. Its ruining the diaphragm in it then leaking. Im dam Lucky it didn't blow up the distributor or cap! Its hooked to manifold vacuum sorce on the 750 race demon carburetor. The motor is a very healthy 340 with a 242 247 @ 050...

As the title says a few search's gives limited info/options on drag radials or slicks ava for 14 inch wheels. Id like to keep using my 14 inch rallies if at all possable. Back in the day I used to run 28x9 15 mickey Thomson slicks. Some 26-27 x 8.5 14's would be perfect! Any thoughts?

Has anyone thought of running one of thease kits on there blow through carb set up? With a 10 position knob (each click of the knob is equal to 1 jet size) in car to adjust on the fly. Combined with a wide band it would "in theory" be best of both worlds for a blow through setup! I found a...

Im selling my Clifford aluminum slant six intake manifold & the 4bbl carb adapter for it. I have decided to take a diffrent route on this project. Its in excellent condition with no modifications or grinding what so ever. Has attaching hardwhere for the adapter aswell $240 plus shipping. Thanks

Hello fellas im checking here 1st to see if anyone has a slant six 4bbl intake manifold they would sell. Im looking for the shorter runner style. (Not long hyper pack style) offy, Clifford. It will be for a neer future turbocharged slant six. Thanks guys!

Anyone out there installed aftermarket anti sway (front) on a non factory sway bar car? im talking 1963-66 a bodies. mines a 1965 dart & looking to possibly put an anti sway bar on er if possible. thanks guys!

Any one know if the pertronix 71385 will work in the factory hi-po 273 prestolite distributor? I know the 1385 igniter works just fine. Would like the rev limiter feature of the igniter III if it will work. Thanks

So ive got some extra parts and 2 bolt on yoke a-body main shafts (i run a trunion style yet in my dart) that are in good shape except for some small rust pits on the bearing surface for the roller bearings that ride inside the input shaft. Anyone think welding them up & turning them down to...

Just as the title says, I noticed during my trans swap that the 273 had some end play. So I mouted a dial on it & checked it. Hot it reads .009-.010. Cold ill get .007-.008. I know its on the very edge of specs. Should I concern myself? Or just enjoy driving er? I know it wasn't thay loose when...

Asking borg & beck style p.p. gurus. Ok Iive confirmed that rite @ about 2000-2500 rpm I can actually see the release fingers swing out & make contact with my release bearing! At idle its fine & I have the 1/ 12 free play in (dead space or take up) my clutch peadle until engine hits 2k on up you...

Anyone ever use any twin disc springless hub clutch's? I ask because I have a McLeod rxt twin 10 made for my stock 9 1/2 setup. Its is a no joke setup will not slip but my question is are thease guys common for slower shifting (more spinning weight on input shaft) also are they more prone for...

Hey fellow mopar people just finished my 4-speed swap in my 65 dart GT. Speedo was perfect before swap, now it reads 8 mph fast! A little resurch found out early 904 has 7 teeth on output shaft. 833/727 have 8 teeth!!!!! (RRRRRRRR!) SO! Inow need a 19 or better yet a 20 tooth early speedo...

Well fellas as some of you know ive been working with Gary Seaward & Lee @ McLeod clutch to put together a "end all" clutch for us guy's & gal's who dont wanna change ove r to the 10.5 set up/fab parts to work. McLeod has done it! Im working with them to get this ava in the catalog to! I used...

Hey guys need som help! Why the f@$k! Is my fresh 1965 833 when it gets warm & cruising for a while it puks gear oil from the vent!?!?!?!?! Its not over full I don't understand it? Wrong fluid? It jas g-l5 80-w90 valvoline gear oil in it. HELP!

Have any of you guys & gals done business with this company? Just getting opinion's. They were the best deal around for the shifter boot & bezel I needed for my car. Has a hump out of a 66 barracuda so I neede the oval boot & bezel. Seemed a little strange when answering the phone just said...

Hey all, im getting parts lined up to install a 65 4-speed in my 65 dart gt with a heathy 273. My qustion is has any of you early a-guys ran or tried this RAM clutch at all? Got all early a parts bell, flywheel & rekated parts. Don't wana halfta go to 10.5 to prevent slippage if at possable...

Seiing whats out there im looking for a early a body 4-speed hump for my 65 dart. Gonna make the swap in the neer future! Thanks guys!

Just kicking some ideas around (bench racing) ive got the o.e. HX35w off my 95 cummins 12v & wondering if I did the 60mm up grade to the compresser & got an exhaust housing for a 1st get cummins if it be enoph to work on a 273? The exhaust housing is 21 cm vs the 12cm thats on there now so it...

Hey guy's im looken for a STRIGHT pass side a body axle. stock axle small bolt pattern. mine the flange is bent! thanks.

This is not mine @ all but ( if I were closer it would be mine!) it is too cheap to not post here for my fellow 273 people! https://cf.searchtempest.com/go-1.1.html#http%3A//kalamazoo.craigslist.org/pts/4857537248.html

Hey guys so my efforts to find a D4B edelbrock intake keep comen up short. so I'm asken for any other dual plane intake options that can be "made" to work with my small bolt heads? Swapen to later heads is out of the qustion. Just looken for ideas I'm not aposed to using washers if that will...

Any one have an edelbrock 500 cfm AVS carb they would like to sell? dont care if man or ele choke. Thanks.

Just as the title says. I've noticed over the last 2 fuel ups @ to diffrent stations that now out of the blue the ol 273 seems to wanna hesitate a bit & from low engjne speed if you hammer it it pings now! Wtf?! This car has NEVER pinged in the last almost 2 years of being rebuilt! Timing hasn't...

Hey guys worken on a 70 383 hp & was wanting know what the maximum difference in the valve stems installed is. So other clown has been working on this before & using a stright edge across the stems.is .030! That sounds like too much to me for non adj rockers! All the intakes are a bit taller...