Search results for query: *

2 15 x 4 wheels and 2 15 x 10 wheels. Rear have 4 1/2 backspace. Rear also comes with 28 12.50 15 Mickey Thompson Sportsman tires and tubes. These tires are not new, i don't even remember when I bought them. They have been sitting in my garage not mounted to car. So I can't say how good they...

These were purchased from member BadDart. I have the lower arms and adjustable strut rods. These arms allow the use of coil over on your a body. There are several threads on this site to explain what they are and a video on you tube that explains how to install them. These have never been...

Adjustable strut rods. These fit A bodies. Not sure of the manufacture. Never installed. Looking for $75 plus the ride. Located in Chino Hills Ca.91709

If you are looking for an a body motor plate Andy at AR is now producing them. They are 3/8 aluminum and profiled. Here is the picture of the one I purchased

Redline Gauge dash insert with Autometer Sport Comp gauges. Comes with electric voltmeter, mechanical oil pressure, electrical temperature, electric fuel level(0 to 90 ohm), tach and electrical speedo(comes with sending unit) also painless wiring light and wiper switches. Located Chino Hills Ca...

If you are looking for a less expensive alternative to PTFE lines and fitting check out this site http://www.frozenboost.com. Not only do they sell fittings and lines they sell it cheaper than anywhere else. an example is a -8 line @ $3.49 a foot which is cheaper than most standard braided line...

Mopar Performance P5249807 - Mopar Performance Cast Air Cleaners Air Filter Assembly, Round, Steel/Aluminum, Black Anodized Top with Mopar Logo, 2 3/4 in. Filter Height. Is in great condition, as far as I know it has never been installed, it has been sitting for a few years in my garage. Located...

I am selling a B@M pro ratchet shifter. I switched over to a Cheetah. It has been mounted for mock up but not used as of yet(only the shifter,not cables and hardware). I also have a pistol grip handle with a button for line lock or whatever you need. I don't have pics as of yet as it is still in...

Selling 3 groove aluminum crank pulley. Condition is fair, has some nicks. Looking for $20 plus 10 for shipping. Located in Chino hills,Ca. Should fit 6 bolt small block cranks

Autometer tach model # 3904 with shift light and a 1 5/8 roll bar mount. Used very little, went to in dash tach. Lists for 219 plus 30 for the mount. Looking for $130 plus 15 to ship. Located in Chino Hills,Ca.

This should fit most a bodies, it came out of a 1973 Dart. It is in good working condition and there are mo broken blades on the cage. Asking $35 shipped. located in Chino Hills, Ca.

swinger bumper, no mounts, just the bumper, good for a core for re chrome or daily driver. $25 prefer not to ship. Located in Chino Hills Ca

Bought this a while back but decided to go electric. No gasket. Looking for 35 plus 10 to ship. Located in chino hills, Ca.

These are are production door handles.Should fit 70 and up, not sure what other years. Don't know origin of manufacture, I bought them off e bay a while back and decided to go with a different style handle. Looking for $40 plus 10 to ship. Located in Chino Hills, Ca.

Part # P5007380. This is a 4 barrel intake for the 5.2 and 5.9 magnum style motors. It can be ran with a carb or have the injector holes drilled( you can see in the pic where the holes would go as I marked them ) and run fuel injection. I bought this as I was going to use a carb but decided to...

5204HKR 70–72 Dart/Demon/Swinger/Duster /Valiant/Diplomat/Volare (A & F Bodies): 318–360 Full Length Tube 1.75" O.D. x 38", Collector Size 3" O.D., Collector Length 10", Port Shape: Same As Port, Black High Temp Paint These are in great condition. There are only 2 small dings in one...

Looking for the grill and headlight bezel off a 69 valiant, Pm me if you have any.Thanks

This fits dart swingers 1971-1973,is new and ready for paint. I also have the lights as well. There is no bracket included with the sale. I will post pics asap as my camera is missing its charger cable and the new one is on the way. Prefer not to ship due to size and possible damage. This is an...

Located in Chino Hills,Ca. I assume it needs rebuild.Asking $35

I have air compressors for sale. The first is a Craftsman 6 HP 30 gallon oil less upright. It is fairly new but looks old as it was stored outside and is faded, Works excellent. $70 The second is old and needs work. It has a compressor from Harbor Freight but still needs to be installed. The...

Front bumper for 1970 -1972 dart. Good for daily driver.Includes brackets. $60. Located in Chino Hills Ca.Prefer local pick up

Bumper would be good for a drag car as it needs some work,I don't know the make as I bought it as a package deal. $40. Located in Chino Hills,Ca.

New rear bumper from AAR. Ready for paint(picture shows sanding marks),holes drilled for brackets. I also have the lenses as well.$75 for the bumper alone and $125 with the lights. Located in Chino Hills,Ca. Prefer local pick up

I have a pair of racing seats. These are the poly seats from Summit Racing. Includes covers,adjustable brackets as well as the mounts for support on the roll cage. These have zero use,only one was installed for mock up. $100 for the pair. Located in Chino Hills Ca prefer local pick up as...

Looking for dash frame for 70 and up dart. refer So Cal area. Don't need the guage cluster,glove box or heater controls just the frame,thanks.

Looking for taillights for 1970 Dart or 1971 to 1973 Scamp as complete as possible, thanks.

I like the no chrome look and wanted to eliminate the moulding around the front and rear windows. What years if any did they not use the chrome strip,I found a picture of what I am looking for and it appears to be a 1970 or 1971, but this is the only one I have seen without it, thanks for any...

How diifferent are the 70 vs 73 swinger rear bumpers, in other words can the 70 bolt up to the 73 brackets, if so what other issues may come up. I am going to fiberglass ones and I like the 1970 look. Thanks in advance.

Well not really bolting, more like glassing. Has anybody tried to glass a pin on hood, maybe adding some support in the area of the hinge, if you removed the springs and then used a prop rod to hold the hood when open. Also this would help support the rear area and eliminate some of the lift...

Just read an article in the Sept. Mopar Muscle mag on Retrotekhttp://retrotekspeed.com fuel injection systems. Looks like a nice setup as it uses a standard carb configuration and can handle up to 500 HP on return less and 500+ on return systems. It is a little pricey (2100) but compared to...