Search results for query: *

gonna upgrade to 95 amp one wire alternator, I know I need to bypass ammeter, if I run a new heavier charge wire from alternator too starter relay and tie ammeter wires together, where do I get power for the rest of the accessories, key switch power etc.? Do I connect the original alternator...

I am having trouble getting full throttle on my Holley 4 barrel carb. I have an aftermarket cable bracket, the original bracket is too short because I am running an Edelbrock air gap intake. I can't use the mopar adapter on the carb because of the design of the cable bracket. I've tried...

I have a 0.030 over 340, 10.5:1 compression, Edelbrock air gap intake, headers, big valve "J" heads with mild port work with a .513/.533 lift, 234/242 duration @ 0.050 Lunati Voodoo camshaft, backed by an A833 four speed and 4:10 8.75 Sure Grip. Topping it off is a Holley 750 double pumper with...

I have a 1969 340 Dart Swinger, the transmission is original to the car, I'm wanting to order a rebuild A833 from Brewers. Can anyone tell me the diameter of the front bearing retainer and tail shaft spline count? They offer 4.354 and 4.805 diameter retainers. And will the output spline count be...

Can someone tell me where the post that hits the canceling cam is located? I have a Grant steering wheel on my 1969 Dart Swinger. Is it a post on the back of the steering wheel hub, or a spring that goes between the wheel hub and steering shaft? Where do I find the part, part number for it? Just...

What are you guys using for cable and bracket? I have a 1969 Dart Swinger, 340 holley 750 double pumper sitting on an Edelbrock RPM Air Gap manifold, four speed car, looking for suggestions and sources. The stock bracket and cable are not going to work.

I will be running Evans Waterless Coolant in my 340, block has been dry since it came back from the machine shop, all new hoses, new radiator and heater core. My questions are...since this product has a boiling point of 375 degrees, is there any need to run the standard 16 pound cap? Will a...

I installed a new torque shaft I got from Brewers today, new balls, bushings, retainer clip, put the plastic washer on the pin, then the peddle linkage rod, but for the life of me I can't get the spring clip on between the rod and the head of the pin, what could I be doing wrong? the clip...

I was ask a question the other day....what is the maximum cam lift you can use with 1.5 stamped steel rockers? Any idea?

Has anyone installed a windshield or back window in a 1969 Dart or similar vehicle? My windshield had a bullet hole in it and back window shattered when I bought the car. I have a new windshield and used back glass, and new gaskets. Just wondering if it's something I should try myself or if it...

Look at the rod parting line on the top rod and the one on the bottom, is the one with the narrow parting line cast, or forged? They all have the same numbers on them, but this one looks different, any idea why?

Any suggestions for the best fitting headers for my 1969 Dart Swinger 340 four speed? I'm on a budget, planning on painted header and wrapping them. Just looking for headers that fit well without having to beat dents in them.

Need help finding the quarter glass trim for the drivers side of my 69 dart 2 door hardtop. It goes on the leading edge of the window and has a rubber seal that seals between the front and rear glass. Have been looking with no success. Anyone have one for sale or know its nomenclature or part...

Looking for the chrome seal carrier that goes on the leading edge of the drivers side quarter window for my 1969 dart, 2 door hardtop swinger. Also can anyone tell me...can the windshield and back glass be installed with the trim clips in place, or do they need to be removed.