Search results for query: *

Who did you send it to?

Lol, I’m no expert in electric but I can usually troubleshoot, but this issue just kicked my ***. I truly hope you do find it

Please do.... if you figure it out. I’m frustrated beyond belief with it.

No, still nothing as far as backlighting for the gauges and speedometer. I do have the turn signal indicator and high beam indicator lights but that’s it. I’ve checked fuses, power to the orange wire on the back of the cluster.... just about everything I can think of but still nothing. I’ve...

Would a 73 three speed motor work in my 72?

I made a mistake when I said nothing broken or missing in that earlier post, I opened it up and seen I’m missing the plastic piece that fits on top of the latch assembly, the one that activates the park switch. Is there somewhere you can buy these ? Or is this a part I need from a used motor?

I added a ground wire from the cluster and the headlight switch. I made sure all the socket tabs are contacting where they should be and everything is clean. Now both turn indicator lights work and the hi-beam indicator works so I don’t think it is a ground issue. I am working outside in...

I’m going to put a ground wire from cluster to a ground point tomorrow, but was wondering... my new headlight switch has a ground spade on it, but my original didn’t, should I hook one up to it too? The dash lights didn’t work with the original switch either. Also the hi_beam indicator lights up...

Ok, I know it takes me awhile, but I been working on other issues. All the bulbs and sockets are new, headlight switch is new. The right turn signal light in the cluster works if the car is running but just stays solid if not running with the key on but nothing else. The heater control and shift...

Ok, is the orange wire in the round connector that plugs into the back of the dash?

I have no dash lights.... the heater control light and shift indicator light comes on , but the dash is a no go. Any ideas?

Ok, got the motor off and checked inside.... nothing broke or missing. But when I hook the battery up the first setting of the switch sounds like it’s on the slowest setting the second and third sound the same , like it’s on the highest speed. I changed wiper switches and it acted the same, the...

Ok, what do I need to do to fix that? Or do I need a new motor? Thanks for all the reply’s everyone

It has the ground strap on it, is there somewhere else the ground issue could be?

As the title says, could it be the switch or the motor? It on a 72 dart with 3 speed motor.

It took me awhile to get it to my house , but that did the trick. Thank you bad sport

I put a strange Dana 60 in the rear with 11 inch brakes, I was wondering what other people used for e brake.cables. When they did this swap. What part # they used for divers side and passenger side. Maybe something that is off the shelf I could pick up locally.

I'll give them a call. Thanks for the replies.

Ok, thanks. Where would be the best place to get them from?

Ok, my rear seat is a 72 dart seat , but my front buckets are from a 67 dart. Is there someone that makes a cover for the rear seat that will match the 67 front seats? If so let me know who please.

I switched from a 10 in drum to a 11 inch drum , now my rear e brake cables are short . Is there a part number I can order that will fit the new 11 inch drums? Any info will help. Thanks

Ok , it has the bimetal spring plate in there but I just didn't know if something else might have been missing. Also looking down through the top of the carb it has an open hole that leads into the chamber where that bi metal spring plate is, should it be open ?

Thanks, rumblefish , is there a link to see those geometry correcting kits?

on the back of the carb body there is a plate with 2 screws, inside it looks like some sort of spring with a small brass plunger. This carb was missing pieces and I'm not sure if anything else goes in there. I can't find a diagram anywhere that shows this plate or the parts behind it. It is a...

If I zero deck the Pistons will I need shorter than stock pushrods? I do have a set of blackjack headers with 1 5/8 tubes, and I will get the heads cleaned up with a 3 angle valve job. I've had this car and theses parts in storage for the last 24 years so I've been out of the game so to speak...

Ok , thanks for the input. It is going to be street driven only.

Hi all, new to the boards here and have a few questions I hope I can get some input on. I'm planning a 360 build , I have KB Hyper pistons and a purple shaft cam 2992 w/ 280 duration and .474 lift and 340 X heads. Also a Strange S-60 rear with 3.73 gears.I'm in the process of rebuilding a six...