Search results for query: *

1967 Dart , power booster(new), KH 4 piston front disc brakes with 9" rear drums, no rear proportioning or hold off valve. The problem is it feels like the rear drums aren't really doing anything when it comes to stopping-I know 9" drums are the best but you should feel some braking. I've...

Does anyone know if Rick is still at Laysons, the last 3 emails I sent to him this week were rejected by their server?

I sent a front fender brace to a fellow in Georgia so he could use it as a sample to start reproducing the part BUT either Canada Post or USPS has lost it. Worst part is I borrowed it from a friend!!If anyone has a spare brace you want to sell, it's for a 67 Dart but probably the same right up...

I'm looking at installing a Rostra electronic cruise control on the 67 Dart but have a question regarding the VSS. I want to install the VSS on the back of the speedometer head then connect the existing speedo cable into it. My question is all the listing for VSS say " fit's standard GM speedo...

I recall there should be a rubber block that mounts below the tail light and fills the gap to the bumper(1967 Dart). I have never seen this item from any of the repro rubber guys, does anyone know who carries it and possibly a part number. Don

Need a set of 1967 , 4 piston caliper disc brake dust shields. Thanks, Don

Looking for a set of disc brake dust shields to fit 67 style 4 piston calipers. Thanks, Don

I would like to install a power seat track in a 67 Dart with a bench seat. Does anyone know what might fit and have you done this before.

Need a complete jack, not looking for anything date coded just a good working jack.

Well it looks like the front intake seal is leaking on the passengers side and of course it under the A/C compressor so it's difficult to see. I've ordered Fel-Pro MS90009 gasket set (67 273 4V) which I believe contains the steel intake to head gaskets. So before I start there are a few...

Maybe this part doesn't exist but this is what I'm looking for. Edelbrock performer carb fuel inlet fitting 5/8-20 that has an inverted flare for a 5/16 fuel line. I've seen them for a 3/8 line but not 5/16. If anyone has a part number or supplier please let me know.

Let me begin with the first picture of the filler neck vent tube, all looks right here. And the vent tube exits through the rubber seal in the trunk, the open end appears to be within the frame rail Now looking at the gas tank itself, there is a fitting near the top of the tank that is...

Need a clean pair of disc brake backing plates to fit 67 Dart with 4 piston KH calipers. Thanks, Don

I'm restoring a set of wheelcovers and want to confirm the correct finishes.The set I have appear to be original, the back section is semi-gloss black, the center of the spokes is a textured light silver and the section around the lug nuts appears to be a cast gray?? Can someone confirm this...

Is anyone reproducing the wide style 67-69 A body rocker panel moldings. I've seen the narrow 3/4" style listed but never the wide or full style molding.

I just finished an A/C conversion on the 67 Dart and want to ad the airtemp decal to the right side quarter glass but not sure of the correct placement. I know it's down low on the glass but should it be just behind the front edge of the glass or towards the rear. A picture of a factory applied...

I need to replace the transmission driven gear in a 904 to calibrate the speedo due to a rear end change. From what I've read it sounds like there is a bit of a trick to index. Can someone offer some help here? Thanks, Don

The gear set in my 67 has started to whine at 40 mph and rather than get into it would like to swap it for one from a 73. The one I'm looking at is the center section with gears but no axles. Will my 67 axles and brakes fit this? From what I have read it looks like the flange to flange distance...

Is there an easier way to remove the strut rod other than having to remove the LCA? Retired mechanic from the dealership said they used to cut the rod, replace the bushings , then weld it up, not my way of doing things but guess if your flate rate you'll make an extra buck. PO installed poly...

Need a pair of the wide style rocker panel moldings for a 67 Dart GT. Anyone have a nice set they want to sell??

Does anyone know of a supplier for factory type seat springs?

Looking to upgrade the old 7 1/4 to 8 1/4, needed for a 67 Dart, prefer complete with brakes, 3.23 gearing or down, open or posi. Prefer around the Ottawa area.

Noticed the pinion seal is leaking, PO replaced it not long ago so before I tear it down want sone feedback on installing a repair sleeve on the pinion yoke or should I just buy a new yoke.

What is the purpose of the 9'th terminal between the coil and outer spark plug terminals??

The noise drives me crazy, it creaks and squeaks even just sitting in the car. Looks like the prior owner put in polyurethane bushings. I lubed them once but the noise returns. Suggestions??

Newbie Mopar owner question.I have a 67 Dart with a 273, Edelbrock 500 cfm carburetor.When cold it starts perfect , just tap the gas to set the choke and starts fine. When the engine is at operating temperature and shut off and then try to restart after say 10 minutes it acts like it's flooded...

Hi, My name is Don and live south of Ottawa along the St Lawrence River. Although it's been a few years since I've owned a Mopar, guess its more like 34 years, I've been restoring cars for about the same time.Just bought a 67 Dart GT(clone) and hope to get to some of the local shows and cruise...