Search results for query: *

What is the size/Diameter ?

I had PRC custom make an aluminum radiator for me for $600 Look at their stuff. Performance Rod & Custom Boonville IN All tig welded, Great looking seams, Oil cooler in radiator, all very well done. Highly recommended.

I have been told that an Open plane (One big opening) gives higher Upper torque, and a 4 hole spacer gives better lower end torque. If I go with this 4 hole version Mr. Gasket 3406 Mr. Gasket Carburetor Spacers | Summit Racing (Mr Gasket 3406) I wonder if the Carb butterfly's will have enough...

Hey ! You are Da Man! and thanks for the Education and the link. DavidK

I have a 340 HiRise intake that has only the smaller bolt holes. I would like to add a 1 inch spacer (Wood or Phenolic, not aluminum) for heat soak issues, but cannot locate a spacer that uses the smaller bolt pattern. The carb is a 1406 Edelbrock with both size patterns. Any suggestions? Please...

Hey Guys, guess I can join your club now. I was really tired for a few weeks and Dr sent me for a Stress test I failed so then to cath to check blood flow. The widow maker was 99.5% clogged, the cardiologist introduced me to the cardiac surgeon and early the next morning when I woke up they...

Would there be any value for 4 of these to anyone?

I have 4 of this center piece but not sure what it goes to. Anyone recognize what they came from?

HVAC Service guys always told me, that as a furnace they turn into an Electric Heater when the Temperature gets around 35-38 degrees and lower. There just is no heat to pull from a cold day. so there is no heat pump activity occurring, just an old school expensive electric furnace.

Great answers. They stay. Thank you!

Since my garage is not heated and uninsulated, each year about this time I turn off the water, move all my waxes and paint cans to the basement. I was wondering if I really need to also move my wd-40 and other aerosol lubricants too. Do you? Should I?

what is unique or bad about "134a replacement"? is the replacement the 1234yf ?

I was careful to not get the can with additives, and they all say: Meets or exceeds AHRI 700-2006 and SAE J 2276 purity standards I wasn't sure if there was different chemical formulas that might not mix well with others. David

I was recently shopping for a 12 oz can of 134a and noticed that some places it is as low as $8, and others it is $22 a can. Is there a difference between the cheap and expensive 134a freon? if so what do I look for? David

Bushing Install Tool is still available with a price reduction. Interested?

With the correct info provided from here I have it on order. Thank you, guys, for the guidance.

I assume I have to have the "cup and gasket" under the block off plate. then it may not leak? based on info here I found Sumit has P5249639 Mopar Performance P5249639 This is making me Happy to get a solution.

See you guys are great at educating the challenged!! Thank you for info. I did make a Block off plate and after less than 100 miles I had Exhaust Blackness all around the block off plate. I would be appreciative for advice on revising the block off plate I made or Gasket material.

Casting number 3512100 the image below is what I have. I was told it came from a 71 Duster 340 and was called a Hi-Rise Intake. Please correct me if I am wrong. any other info about it may help me in the future.

I made a block off plate for an EGR opening on a 340 intake, it leaked Exhaust all over the intake manifold. This is Hi-Rise Intake from a 71-72 Duster. I cannot find a part number for the Gasket, so I made a gasket from a sheet of Cometic C15180, specs say it is good to 1200 Degrees F. I think...

Our local Samsclub only sells Duracell. Most have 36 month warranty. I didn't notice any AGM.

I cleaned connection points and unplugged/reconnected. Now the maximum voltage at high RPM is 14.6V I do have a Battery Maintainer that auto identifies it as AGM. it backs off at 13.1V to a very small current. I will watch it a while and then get another AGM. Googling Battery Reviews is a joke...

I check for voltage drop and did have .74 Volts between the Battery and the IGN connection on the Voltage regulator. the drop was in the Ignition switch on the column. Replaced it and now it is .51 Volts Still testing all the connections between the two points.

Dana67Dart: Tuff Stuff support said 15.1 was ok. What should the max voltage be? It is only driven once every two weeks for a pleasure cruise. It could have been my cheap trickle charger. I just got another one last week.

AJ: It usually starts increasing around 800. I don't have a very good Tach, its only has a 2 inch face. sorry for the confusion. Do you or others use AGM batteries?

I have a Tuff Stuff brand Voltage Regulator(7545) and Alternator(8509RCDP). Until it gets to 1000RPM the voltage output is 12.3 to 12.5 At 900RPM it is 14.6 and at 1000RPM it is 15.1 Over 3 years I killed my AutoZone H7-AGM. This AGM normal sitting voltage should be 13.1-13.4 its only 12.3 and...

Used one time, no scratches, dents or dings. like new condition $80 Distributor bushing installer and reamer tools are designed for effective use on Chrysler, Dodge, and Plymouth small or big block V8 engines. They perform two critical functions for your successful installation. Utilize them to...

The top side play is very small but noticeable. I set the reluctor gap to be .008 If I press the reluctor towards the pickup, I cannot get a .006 feeler gauge into the gap. It does not touch the pickup. I don't know what brand of distributor this is, so most likely cannot get a bushing to fix...

i did not see what @halifaxhops wrote? only the Disagree thing? please repost @halifaxhops.

318 Stock Engine. When setting the reluctor gap I noticed that if I push/pull the Distributor shaft it has a small amount of play. The reluctor does not touch the pickup. What side to side play is acceptable? I have zero play at the bottom side to side or up/down. I just replaced my...