Search results for query: *

I have a Fuel Air Spark Technology XFI stand alone EFI system that I ran on my 67 Dart for 8ish years. The kit is intended for a 5.7 or 6.1 Gen III Hemi, but the ECUs are capable of supporting many other engines with different harnesses. I recently pulled my 5.7 Hemi, built a 6.2 Hemi stroker...

I have a manual steering box that I just removed from my 67 Dart. It has not been rebuilt and does have some play, but it's usable as is for sure. I'm upgrading to a quicker ratio, so I no longer need it. $60 plus shipping from 80403.

I have quite a few gen III hemi parts I’ve been holding onto for another build, but I’m gonna have to go through my trans this winter and need to free up some cash... Basically I have a 05-08 5.7 hemi top-end, and then all the bolt/basics to add to a short block for a car 5.7. 05-08 5.7...

Looking for a drivers side hood hinge. Mine gave up the ghost, end while prepping for the gas strut swap I discovered mine is slightly bent. I’m guessing this played a part in the failure so I’m looking for a new one! Joe

My drivers hood hinge is stuck, hood won’t close, it just flexes the hinge into the fender... 67 dart, steel hood. Any suggestions?

I have a spare 5.7 hemi "car" intake manifold for sale. It is in good shape all ports, holes, and vacuum posts are intact. This should fit any 2003-2008 5.7 hemi. I know modern muscle makes adapters for your accessories to switch from a truck intake to this as most guys seem to like this look...

I'm looking for a car eagle intake manifold ('09 or newer) as an upgrade on my early 5.7. I figured I'd have better luck from most you hemi guys here than I would in the parts wanted section. Let me know what you've got! Joe

I have a set of Large Bolt Pattern disc brake spindles for sale. I picked these up when I switched to LBP and ran them for the last 2 years until I switched to 2" drop spindles to lower the car a bit more this winter. They're cleaned up, painted black and in good shape ready to run. $120+...

I have a Hughes performance mild converter for sale. It is part number 24-20. It was behind my 5.7 hemi for about 1000-1500 miles, I swapped to a higher stall converter, and am now selling all my 727 stuff for a 200r4 swap. This is a great converter for a cruiser, neutral balance, 5/16 bolts...

I have a starter for sale that I used with my 5.7 hemi swap when I was running a 727 trans. It is the 2005 truck starter, manual trans, that seems to be the best starter for the swap with TTI headers. I have switched to a 200r4, and it will not fit with my Reid Bell and JW wheel flex plate. I...

I have a Hughes performance mild converter for sale. It is part number 24-20. It was behind my 5.7 hemi for about 1000-1500 miles, I swapped to a higher stall converter, and am now selling all my 727 stuff for a 200r4 swap. This is a great converter for a cruiser, neutral balance, 5/16...

Thought I'd put this here as a lot of hemi guys don't always look in the parts for sale stuff... I bought this new, SFI rated flexplate for the swap, I'm pulling my 727 for a 200r4 and don't need this anymore, about 2000 miles on it before it was pulled. Hardware included, send me a PM. $80...

I need some help from you transmission guys, as I have never jumped into a auto trans before. I have a 727 with about 1500 miles on it. It was rebuilt quite a bit (years) before I fired up the car. When I fired the car last year I had a very small front seal leak, it has gotten worse so I...

Looking for a clean pair of fender braces for a 67 dart. They bolt to the front bumper bracket, and attach at the lower front fender near the wheel wells. My fenders are wavin' in the breeze since I got it running late last summer! Let me know what ya got! Joe

I have a Hellwig 1 -1/8" front sway-bar (part number 9506) with all mounting brackets and hardware. This was used for mock-up only, removed before car was driven, so it is truly NEW. I went a different direction with my front suspension and don't need it. This should fit any 67-72 a-body, not...

I am doing a BBP swap with a rear disc upgrade on my 67 dart, with a 8.75 rear. These parts have less than 500mi on them, worked well, and are in great shape. Included is new rear drums, backing plates painted black, wheel cylinders, all hardware and springs, and brake shoes. The only thing I...

I'm looking for a Grant repo "tuff wheel" the woodgrain one, WITH rivets. The new wood one they produce doesn't have rivets... Lemme know. Joe

I have a set of pin type caliper brackets I'm not going to use. These are for the 10.95 disc brakes and orig came from a '70 E-body. Will work for a BBP disc swap with any BBP disc spindle. $45 shipped to you.

Looking for a very clean/nice fuel filler tube for my 67 dart. Mine has a small crease and doesn't seal with a new gasket and tank... tired of the smell... Im in denver area JOE

I have a edelbrock 1405, 600cfm manual choke that's just been sittin. It was running when removed, by I'm sure needs a rebuild by now just due to age. $75 + shipping from 80212 Joe

Looking for a clean/nice rearview mirror for a 67 dart. I managed to break mine and can't seem to find the right one as a repo... Thanks

I put a valiant dash in my dart and am looking for the (seperate) radio and heater bezels for it. My plan is to paint or wrap them so they don't have to be perfect, as long as the tabs/screw holes all look good. Lemme know Joe

I'm making progress towards a start up... I've found conflicting info and thought you guys would be dialed in... 5.7 hemi from 2005 car, what is the flow rating on the factory fuel injectors at 58 psi? 26lbs? 30lbs? 32lbs? Thanks in advance Joe

I stumbled across these seat badges for a 67 GT I forgot I stashed a while ago. I have the 4 that I need... they are in great shape, backs, nuts/clips all included. $80 + shipping from 80212 for the pair... JOE

I have 2 RIGHT tail lights from a 69 that I do not need. I would say these would be clean drivers, especially with a good polish and repaint of the black area. The chrome is in good shape, no cracks or bends in the bezels. The lenses are in very good shape without cracks, hazing, or divots...

I have a black console from a '69 Dart, the chrome is really good overall, there are a few scratches in the black shell but nothing really bad. What you see is what you get... I don't have brackets/shifter. $120 plus shipping from 80212

I have several 440 parts I am selling, these parts are brand new in box, I am posting them for my brother as he is going another direction and not going to put them to use. I Also have a 440 block/crank/heads for local pick-up. Prices below are + shipping from 80212 440 pistons $300...

for those of us using a factory K and TTI mounts, I am lookin for inspiration or ideas on a good oil filter location. I am trying to keep it off the the inner fender, but cant seem to find a good location. I have been looking at the passenger frame rail, but not sure I have room on the engine...

Hey guys, I currently have a auto console that is going back into my 67 dart. I am planning to run a aftermarket shifter, and was gonna mount it up under the console using a 4spd top, instead of the auto top for fitment ease... So I gotta build a bracket to mount the shifter... I can...

I have this MSD 6A box that I had stashed away from before I did my Hemi swap... I dont need it now, so grab it for your ride. It worked great when pulled from my previous ride. $75 + shipping from 80212. JOE