Search results for query: *

Anyone Have any tips to remove the power steering unit from 67 cuda? I have 340 with tti headers. I am thinking I have to at least remove one motor mount if not both. I unbolted the header last night. Any suggestions?

I guess gloss black it is. Thanks Dartnut.

What color is the power steering units suppose to be on 1967-69 abodies? Gray or Silver I have seen them both ways.

I put 195/65/15's on the front until I can find a set of series 40 rims 15x6 or 6.5 with 4 and 1/4 backspacing. .

Cudaman51 was nice enough to send me the part for the price of a beer at Mopar nats next year. I pounded on it a little and installed the new piece. Now I have to figure out the tires. Thanks for everyone's help and a special thanks to Cudaman51.

I think what happened is that when I backed the bolt off under the weight of the vehicle that when the bolt shot out with force that the finger became wedged in the lower control arm. Redfish I did what you said and the lower control arm does come down. The finger is still stuck. Now I am going...

I jacked it up and removed the bumper.Then let it drop and still too much tension for it to move. Torsion bars installed wrong?

Maybe when the bolt shot out it came down with force.

redfish, I took off bumper for upper control arm. Jacked up the lower and nothing. I even tried to pry it a little to see if it moved. It looks as if i jack up the lower control arm that finger would put more pressure on block. Suggestions.

Thanks I am headed for the garage.

I do need to take everything else that I mentioned off correct?

Redfish, It seems as though the swivel part is putting pressure on it. How do I move the swivel part?

If I can't retap the block in the lower control arm. How would I go about removing it. I am assuming I will remove upper control arm,tie rod,sway bar, and shock. I figured I need to get the lower control low enough to remove the tension on the swivel part or i will never be able to get the...

Just getting burned out at this point. Probably worked on car for last 45 days straight unless I had to work a double. Just want to driv ethe car because it has been sooo loonggg. Thats probably half of my problem. I am constantly doing things on the car under frustration or lack of sleep and...

Thanks for the link blue73duster.

68formulas340, if I go down to 15x6 rims will the 215/60/15 fit?

The tire looked like it would clear.

Full weight but I was lowering so I thought I would be ok. The bolt was loose after I had it aligned. I jacked the car up tightened it. Lowered the car bounce it a couple of times then lowered it until it popped out. Three quarter turns.

Went to adjust the torsion bar bolt to correct the height on vehicle and the bolt popped out. The middle of the bolt is stripped and has access steel on the threads. The block which it threads into has the same. Tire is up inside the wheel well and car is sitting inches from the ground any...

Torsion bar was a little off on one side. Took it in for alignent and back to tire shop today.

215/65R15 on 15x7 copcar rims disc brake setup from dart

I am going to take the tires off and recheck everything. I very well could have missed something.

No it does not lean at the top.

Took car for a ride, first time out since 1989. Car was fine when I left the driveway. Drove 3-5 miles and when I returned the driver side tire moved up into the fender. Now I dont have the clearance I need to get the car on trailer for front end alignment. I am going to put the 14 inch rims...

I'll check online tonight. Thanks.

Thanks for the help.

Does anyone know where I can buy a rear shock mount stud to bolt into the plate (below the axle)that is larger than 5/8 OD? Or do I have to buy the plate and stud one piece?

I am going to put the calipers to the rear, but it looks like the bolt on the lower ball joint might hit the tab? I have not finished the project because I am trying to figure out what bushings to use.

I am new to this site and any help would be greatly appreciated. I am recently finishing up my 67 barracuda conv. and I am in desperate need of some help. I converted the front brakes to 74 duster disc. These are my questions: 1.What is the difference between polyurethane bushings and...