Search results for query: *

I still have a few of these left :)

.I have one good vent bolt and three brass fittings left (one "Y" and two "V") I also have a number of vent bolts that don't have the "check valve" working or the top cap is missing. These would attach the brass block to the rear and vent the housing if you were not picky. So any one block with...

This is the pushrod that goes from the master cylinder to the brake pedal on a 66-70 B body with manual (non power) brakes. The special bolt is also included. This hard to get piece has been wire wheeled and painted with Cast Blast. Located in Savannah, GA I'd like to get $15 plus shipping ($8...

After a few requests I've finally cleaned up some of my used 8 3/4 brake line fittings. They are brass and polish up very nicely on the wire wheel. After that, I clear coat them to keep them that way. I also have the special vent bolts that have a "check valve" in them. This is the fitting that...

I have ONE new Magnum 500 wheel center cap with the "Bull's Eye" design used on Mopars. I do not know if it's nos or repro, but since I don't see a part number, please assume the latter. It has the retainer but one of the screws is missing. Again this is ONE cap that I got in a box of parts...

Mine are used originals and I have a couple of sets. Thanks!

I have a set of 2 used torsion bar adjuster blocks and bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US...

I have a set of 4 used upper control arm cam bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US. Merry...

I have one used set of lower control arm pivot studs with the correct washers/nuts for a 66-72 B body or a 70-74 E body. The threads are in excellent condition. The studs have been sandblasted, wire wheeled & painted with Cast Blast and are ready to install. Located in Savannah, GA I'd like to...

This is a set of lower control arms for a 66-72 B body or a 70-74 E body without the sway bar. They have been sandblasted, wire wheeled and painted and are ready to install. I left the shell of the old rubber bushings in the arms in case you want to use the style of polyurethane bushings that...

This is a used manual brake reinforcement plate used on 66-72 B body cars without power brakes. This one has been wire wheeled and painted gloss black. There is some minor pitting but overall it looks very good! Located in Savannah, GA I'd like to get $35 shipped. Thanks for looking!

This is the brake pedal pushrod and bolt that connects the brake pedal to the master cylinder on 67-72 B body cars with manual (no power) brakes. It has been wire wheeled and painted. The bolt and the rubber boot is included. Located in Savannah,GA I'd like to get $35 shipped. Thanks for looking!

This is a used 3 1/2 inch factory steering column coupler for a 67 and up A or B body car with POWER steering. It has the "guts" that go inside the unit, the roll pin to secure it to the box and the top clip that holds it together. It does NOT have the rubber seal (They can be purchased on the...

Yes. My Paypal address is [email protected]

sale pending

This is a used manual steering box from a mid 60's A or B body. It has a 65 date code on it. To the best of my knowledge it is NOT the more desirable "quick ratio" unit. This box was NOT rebuilt. It has been cleaned and painted, adjusted and lubed. It is tight with no apparent slop in the...

This is a good used power steering column coupler for a mid 60's early 70's A B or E body car with power steering. It includes the "guts" that go inside, a used rubber seal which may or may not have any life left in it, the outer seal retaining clip and the roll pin that holds it in place. It...

I'm going to lube it up complete the adjustment and see if I can make it a working part. Thanks all!

Never mind. got the answer! Manual steering box OIL or GREASE ?

actually the adjustment screw helped a lot. If I mess with it I actually may be able to make it work. Are these units supposed to be greased or do they use 90 weight?

Looks like 2267225 with a 65 date code. I put up some more pics. Thanks for looking!

This is manual steering box from a mid 60's A body. To the best of my knowledge, it is NOT the "rare fast ratio" box. The Pitman arm has been removed so it will also work on earlier A bodies, B and E body cars. The problem is that this box DOES NOT WORK! I discovered this after spending hours...

I have four proportioning valves from a and b body cars with drum brakes. They have been cleaned and polished but NOT rebuilt! Selling each for $18 shipped or $60 for all 4. Located in Savannah,Ga Thanks for looking!

This is a 66-70 B body transmission crossmember for an automatic transmission car. It will work on big or small block, even a slant six! This part has been sandblasted and painted. The factory bolts are in it! The old rubber mount is included. It has some age cracks but still has some life in...

I'm leaving tomorrow for the Mopar Nationals and I'm trying to get a little bit more cash to get me there. This part will be offered for $75 shipped for today only. You have to be able to pay with Paypal. I can ship tomorrow or deliver it to the show this weekend if paid in advance. This is a...

I'm leaving tomorrow for the Mopar Nationals and I'm trying to get a little bit more cash to get me there. This part will be offered for $50 shipped for today only. You have to be able to pay with Paypal. I can ship tomorrow or deliver it to the show this weekend if paid in advance. This is a...

This is a stock column shifted steering column from (I am told) a 67 Dart. It is the shorter shaft for a power steering car. The shift handle and turn signal handle have been removed and I do not have them. Overall this part looks to be in good condition. Steering columns are supposed to be...

Thanks for the info. I corrected writeup.

This is a power steering column from a 67 Dart that someone converted from a column shift to a floor shift. I have seen articles on how to do it but never owned one before. I THINK that they did bodywork on the collar with JB weld or something but they could have swapped out the collar itself...

This is a used steering coupler from a 68 A body. It has been cleaned and painted. I have all of the mechanical "guts" that go inside, plus the top lock ring. I do NOT have the rubber seal, they are available on the net and on this group. Remember that the manual coupler is different from the...