Search results for query: *

Looking for a NON LEAN BURN air cleaner assembly for a super six /6 2bbl carb... Also need the carb accelerator mounting brackets . Thanks for looking

Looking for a complete Super 6 setup.....manifolds, bracketry, linkages and carb that will work on my 1980, so I need one from that timeframe. Needs to be within driving distance of Pittsburgh.

Thanks Tracy....picked up a 36 elsewhere before seeing your post.....thanks anyways, and thanks for looking! Still probably looking for a 37 if the 36 doesnt work out to be the right one for me.... Dave

Looking for speedo pinion gears for 727 auto trans. Looking for 36,37 and 34..... Let me know what you have and how much you want. Paypal for payment. Thanks for looking!

Actually I may do that.....I can pick up a metal-stamping kit at Harbor Freight cheap, make the tag and have the tool left over..... Just figured if someone had one for a few bucks that would be thee asiest route.

Anyone? Buehler?

Hi folks I am looking for the little metal tag for the 8 3/4 diff that has the ratio stamped on it, in the 3.55 flavor. ....cant bring myself to pay $16 for a little bitty tag on ebay. Hoping someone has one hanging around they will sell cheap(er). Pay by paypal. Thanks all.

Still looking.

Looking to pull parts together so I can convert my drums to disk... Looking for the "large bearing, short height" spindles from a disk0-brake 73-up a-body or e-body. Big bolt pattern. Let me know what you have and how much, shipped to 15132. Thanks for looking.

How "early" are you talking? What are the differences?

I need the secondary linkage rod for a Edelbrock 1407 carb. Not sure if other models use the same rod or what. Thanks folks!

I know I can probably get these new/repro, but thought I would try here first and save some green.... Looking for the trim clips that hold up the metal trim on either side of the car on the headliner....72 Barracuda. I "need" 4 of them at least....I counted 3 broken and one missing...

Looking to get the dust cover/inspection plate cover and the bolts for it for a small block 727. I can pay by paypal. Thanks for looking!

Got it. Thanks!

Looking to buy a 3.8 ratio intermediate shift lever for a 727 tranny.... Need asap. I can pay by paypal. Thanks for looking.

Looking for the two square washers/shims used on the rear tranny mount. I can pay by paypal. Thanks! Dave

No, unfortunately cant be there......the next show I am going to try to make is the Mopars at Carlisle........... What do you want for it, mailed/shipped?

I need one of the two locating pins found on the back of the 318 engine that aligns/supports the tranny.... Thanks

Any chance the crossmembers are the same between a body and then the two e-bodies??? My guess is no for the first and maybe for the second?

Thanks airgrabber.....can you advsie a newbie on how to best measure the u joint yoke I have? I remeber reading that I have the "small" yoke on the case/gears I have......how do I confirm? By the way....got the steering column collars yesterday....NICE!!!!!!!! :salute: ....and the...

email sent Is there a difference in a crossmember for a 727 versus a 904??

I am going to look in the factory service manual and see if they have any listings... I am also headed back to the dealer tomorrow to pick up parts so I may try and look in their book for them..... I dont know if the 72 was offered from the factory with this combination though...318 and a...

Looking for: Driveshaft and tranny crossmember for 72 Barracuda that is running an 8 3/4 rear end (2.76 gears , small yoke I thin) and a 1976 318 engine.....planning on the 727 tranny.... Would prefer something local/within driving distance of Pittsburgh, PA. Thanks!

Just ordered a set from airgrabber..... Looking forward to getting them!:headbang:

Looking for a good set of floor shift column collars to fit my 72 barracuda. Let me know how much you want, shipped. Thanks!

Congrats on finding your lift. I noticed you said its a one ton. SO that brings me to my question --- is a two ton really needed or wil la one ton work just fine for engines? I guess aside from lifting the whole front end of the car it should be , right?

Cool! I saw a couple of these for sale over the weekend at a classic car parts flea market and was thinking about one.....just $10 for a brand new one! Shoulda scarfed it up....but I figured I was the only one who though they were cool still...LOL I was THIS close and then decided...