Search results for query: *

I just put that exact kit in my Duster. They are brite, but not too bright. It's well put together, but a little bulky with the lenght of the wiring and the protective covering, some of which I stripped off to make it a little more manageable around the connections, the rest I bundled up and...

My grass is starting to take off, i havent dragged the mower out of the shed yet.

Bam…. So close. Time for a break. Maybe till tomorrow when I’m fresh and can end with a good day with no issues.

Someone I know was recently accused of shooting a cat that had a GPS collar on it. I saw the tracing of the collar and it was just like the movies. I'll be buying one for my car. That said, maybe I don't want to know. I don't need a murder charge on top of my problems.

...fully understand it right away, but it worked. My suggestion is to map out the carb which sounds like you're already planning to do. I don't *think* there is anything inherently better or worse with the XP versus an AED. If you want someone to fixup a carb for your situation, then contact...

I'm sure the families of those involved will find significant consolation in that.

Thanks missing linc! I started with the B bodies (my Fury was just a daily beater) but when I found out how much lighter the A bodies were, I quickly did some math and knew it was an easy way to go a lot quicker in the 1/4 mile, which was all I cared about back in the day, LOL. My Dart is an...

A matched set of 4.Very Clean,not dented up.Shine VERY well.$60set of 4.Keene NH.US Postal money order only.

Just got done cutting the grass. It's supposed to rain tonight.

Its about time to upgrade our kiddie pool and i have a thought From the edge of the deck, to the wood retaining wall is exactly 10 foot So I'm considering getting a 10x18 foot pool BUT, the legs don't come straight down So, if I buy this and put it in the hole, it will be supported on 3...

Hey john do you have any summit discount codes left . Thanks .

I Square

Tti Big money. I've bought their systems for customers before on this particular deal. I'm trying to save a couple bucks. The car already has a complete exhaust system. I am just removing the headers and going to the exhaust manifolds and only need a few feet worth of pipe. Aunt, I just wondered...

i see its up and running now

Thanks Scott, I appreciate it!

Thank you MoparCowboy! Glad to know I'm not the only one, LOL. Just wish I started on it a little sooner.

Thanks ocdart - never thought of a 200-4R. What type of torque/HP can it handle?

Not even close to the grunt of a big block, not even the lowly 383. lol The worst thing Mopar ever did is to put a low compression 360 in a 5000# truck

My in box shows as empty

Lookin good Kegan, super solid! :thumbsup:

It's probably NOT the Reverse Idler gear sticking, nor the Slider, but instead is the internal shifter. Try shifting it without the cover. I bet it shifts just fine. If not, remove the detent system off the backend and try again. It should flick in an out like magic. Here's the deal, There are...

Cause your reply to Junkyardhero's answer to YOUR question seems a little condescending.

Well well well. I jetted down the primary from 82 to 77. took a little ride and now cruising at 2600 RPM, level flat ground, I'm now in the 12.4 range. From the 10's. BUT upon brisk acceleration on the primaries only..... BANG! in the 15 range and higher. so take it easy bring it home, and I...

That, I think, is a special bearing, The last one I bought that looked like that, cost me a fortune. It might be worth your time to run over to your local bearing supply store, and have them check it out.

just pick one out, use Marvin the Martians reatomizing enlarging ray and off you go! if only it was that simple

the new trailer I just bought is out of its one year service warranty. So as soon as I get time. I am going to pull the wheels and grease them etc. But mine has the axle Buddy's.

A-833 uses a 308 or 307 bearing.