Search results for query: *

Maybe that's why it don't feel that quick ..One tire spin to get the car moving?

Could I upgrade some part(s) to make it posi ? Or would that require a whole rear end? NICE DUSTER

The factory part number is 2465508 and is the same for both sides.

I just don't answer the door. NOBODY I want to see comes to my front door without calling first.

Also - if I have the choice between a 383 and a 400 block, I'm going to build the 400. Whoever built the first 400 stroker basically rendered the 383 useless. The larger bore of the 400 is a significant advantage when built to whatever the intended degree. Beyond a faithful factory-style...

The factory oil pressure sender and gage used the IVR. The replacement senders do not seem to have the same calibration as factory 60s and early 70s senders.

383 Magnum was rated at 5200 rpm. If you couldn't get your 383 past 4000, there was something seriously wrong with it. If you couldn't get a 383 four speed to roast tires better than a 318 2bbl, there was something SERIOUSLY wrong with it. (I would guess trash valve springs, or a flat camshaft).

Hi friends, I have for sale new reproduction tail light lenses for your 1973 - 1974 Plymouth Duster. Please note in the pictures they have a dot in the middle of the lens. That is from the mold, they all have that. The item ships from México. I have to purchase these from another source so it...

Nope, it doesn't as long as the vent tube is open. It just vents to the outside through the filler neck seal. I've seen them plugged with undercoat, rust, mud, bugs, etc.

Hi friends, I have for sale new reproduction side marker lights in 4 colors for your 1972 - 1980 Dodge, Plymouth or Chrysler. I have them in Amber, Red, Clear or Smoke. The item ships from México. I am offering the lights directly to you here. I will keep you apprised of the movements until...

Hi friends, I have for sale new reproduction tail light lenses for your 1964 Valiant Sedan. These will not work for the wagons. The item ships from México. I am offering the lenses directly to you here. I ship right away and will keep you apprised of the movements until it gets to your...

The 2bbl and 4bbl bellcrank (that bolts to the back of the head) are different. so is the front link between the carb stud and the bellcrank. If you have an aftermarket intake and carb, that can be a chore trying to get it to work right.

COME ON MAN ! Their all GOOD because they are MOPARS !!!! Hell even the late 80's small blocks can run good with a little tweekin'. MY vote is for the 361 B of 1964 !!!:thumbsup:

Hi friends, I have for sale new reproduction tail light lenses for your 1966 Valiant or your 1966 Barracuda. The item ships from México. I am offering the lenses directly to you here. The last two pictures are of a set of lenses a board member bought and buffed. This is what they look like...

Hi friends, I have for sale new reproduction stop lenses and reverse lenses for your 1971 - 1973 Dodge Dart. Keep in mind the stop lenses have a right and left. There is a slight angle on the lenses. We only have one side available. They will fit on both sides but on one side the lens will...

F3 was the original colour. Green car painted red.

This may help too. TDC is when the #1 piston is at the very top of the compression stroke. Top Dead Center Timing is the number of crankshaft degree either before or after TDC the spark will be fired. Initial or base timing: Timing with no advance added. Normally on a stock engine timing at...

Have you checked the FSM? They usually have procedures in them for reinstalling glass. I know the windshield installation procedure calls for sealant on the bottom half. Not sure about the rear glass though.

Here's a nice one, NOT MINE !, WISH IT WAS. Mopar Swap/buy. | Facebook Mopar Swap/buy. | Facebook

Hi friends, I have for sale new reproduction turn signal lenses for your 1970 - 1976 Plymouth Valiant. I believe they are the same lenses on all the models. I have them in either clear or amber. The item ships from México. I am offering the lenses directly to you here. I ship right away and...

Not sure if this was directed at me but if it was, I did clearly say in one of my posts that I have not driven a big block A body so no, I do not have any direct experience with it. However, it seems to be long-standing, common knowledge in Mopar world that was indeed the case with those cars...

Found my answer in the passon book. Thanks for the responses

Hi friends, I have for sale new reproduction fender mounted turn signal lights. These have plastic housings, not metal. They are great for a daily driver. What looks like a defect in pictures 2 and 3 is the plastic over the lights themselves. These will fit multiple vehicles. The item ships...

Awesome. Thanks for sharing. Kim

It should. Paint? Got so hot it melted the led "ball" a bit? Try a knife or small screwdriver to separate the "ball" from the spring Unless the spring is really compressed it's really not too stiff to move by hand.

Not even close, the 383 all day long mild hopped 360 still gets walked on by a 383 magnum bore size makes the 383 have more potential.

Hi friends, I have for sale new reproduction tail light lenses with reverse lenses for your 1964 Valiant Sedan. These will not work for the wagons. The item ships from México. I am offering the lenses directly to you here. I ship right away and will keep you apprised of the movements until it...