[FOR SALE] cams convertas and few more parts

-
Status
Not open for further replies.

earthmover

in the tire smoke
Joined
Sep 21, 2007
Messages
2,401
Reaction score
172
Location
nc
Rating - 100%
9   0   0
Contact seller
9.5 dynamic race verta had behind my 345 would go 45 5000 very good verta did mostly street racing
600.00 plus the ride

8 inch turbo action would go 5 5500 behind 345 same as above street race

lunti solid roller 3 bolt big block
53799
lun 37 up 73 ur 73
282@50
457 lobe
685 lift 1.5 rocker
731 1.6 rocker
26 lash
175.00

cam motion solid roller
I'll get spec tomorrow or weekend
175.00

440 source bullet fly wheel used to break new motor end that's it 100.00

aluminum valve covers 100.00

all parts are plus shipping
these are parts I'll never use again
have a few more I need get pictures of to post
also have a 10 inch b&m verta bought used never used it 200.00

20220129_143853.jpg
20220129_144139.jpg
20220129_143903.jpg
20220129_143542.jpg
20220129_143445.jpg
 
Last edited by a moderator:
Interested in Billet Flywheel to break in my motor when it's done. Mailbox is full. My email !(no emails in public forums, in the rules. (Thank you)

Thanks,
Jay
(Or phone numbers)

Text Ok
 
ok bigmike54
Interested in Billet Flywheel to break in my motor when it's done. Mailbox is full. My email !(no emails in public forums, in the rules. (Thank you)

Thanks,
Jay
Interested in Billet Flywheel to break in my motor when it's done. Mailbox is full. My email !(no emails in public forums, in the rules. (Thank you)

Thanks,
Jay
(Or phone numbers)

Text Ok
is your crank 6 bolt I forgot mines hemi bolt deal I believe
but will verify
 
Last edited by a moderator:
Your inbox is full.



Very interested in the big block cams
 
Last edited by a moderator:
Maybe interested in 9.5 and 8 inch converters. Are they for 904 or 727's, How much? Thanks.
 
What are the specs of the motors you ran those cams in?
Been looking for a solid roller.

This is what I'm working with:

383 with 12.5-1 compression, tunnel ram with dual 750dps
5000 stall converter RMVB 727
8-3/4 4.11 gears
29in tall tires
3800lb car
 
What are the specs of the motors you ran those cams in?
Been looking for a solid roller.

This is what I'm working with:

383 with 12.5-1 compression, tunnel ram with dual 750dps
5000 stall converter RMVB 727
8-3/4 4.11 gears
29in tall tires
3800lb car


was in a 451 never really made good track pass shift noid wire was off
then trans pump was leaking
then found out that crankshaft specialties in Tennessee if I remember right beat me out of my money to fix the crank
was found to be cracked after he calm to fix it


had great power I have a video where the shifter didn't shift I'll try to post

it's not letting me post it
I can email it to you if you inbox me your email
 
Specs and details on your old small block purple shaft?
 
was in a 451 never really made good track pass shift noid wire was off
then trans pump was leaking
then found out that crankshaft specialties in Tennessee if I remember right beat me out of my money to fix the crank
was found to be cracked after he calm to fix it


had great power I have a video where the shifter didn't shift I'll try to post

it's not letting me post it
I can email it to you if you inbox me your email
Your inbox is full.
 
Last edited by a moderator:
is 10" B&M verta still available
 
Last edited by a moderator:
Fellas, phone numbers and e mail addresses have been removed here for your internet security. They are against the site's sale rules. Thanks

Note: I sent @earthmover a message to clean his inbox.
 
Last edited:
cam motion cam specs
273 283
737 int
705 ex
112 love sep
108 centerline
24 lash
 
Status
Not open for further replies.
-
Back
Top