Hughes having a sale on c.c. head porting..

[stroked340]

Just caught this on their site running a discount on c.c. porting heads..normally $1227.00 going to cost $862.00 for my 60179 Edelbrocks..just a heads up to everyone

 

[UDUST81]

yep just sent my heads in monday $725 bucks for my big block procomps, by the time im done ill have around $1800 in small port heads that flow 330 cfm at .600 lift freaking awesome!

 

[rumblefish360]

Yes! At the end of every year this happens. Got mine this way. New heads from then CNC'd to big mouth's.

Sadly, you'll probably get to a finished engine before I get to mine.

 

[70aarcuda]

50% percent off on the CNC work...right?....then the cost of valve job and whatever else needed?

 

[rumblefish360]

Yea. Normal price on the rest.

 

[Ironmike]

Thanks for the head up, brutha. Saved me 367 bucks.

 

[famous bob]

yep just sent my heads in monday $725 bucks for my big block procomps, by the time im done ill have around $1800 in small port heads that flow 330 cfm at .600 lift freaking awesome!

hey udust81, are your procomps raised port ?

 

[stroked340]

Thanks for the head up, brutha. Saved me 367 bucks.

Your welcome they just got my heads..now the fun starts

 

[UDUST81]

hey udust81, are your procomps raised port ?

nope, standard, basically a copy of an edelbrock rpm

 

[Ironmike]

yep just sent my heads in monday $725 bucks for my big block procomps, by the time im done ill have around $1800 in small port heads that flow 330 cfm at .600 lift freaking awesome!

Man I thought for a minute that 330@ .600 was a smallblock number....That'd be nice.

 

[rumblefish360]

Man I thought for a minute that 330@ .600 was a smallblock number....That'd be nice.

Then get a set of CNC'd W2 heads.
The W5's will do slightly better IF you can get a good casting in a set.

 

[Ironmike]

Then get a set of CNC'd W2 heads.
The W5's will do slightly better IF you can get a good casting in a set.

Hell for that matter, W9's can get you in the 380 range. Whole different animal, though...

 

[D-50394]

My Indy 360-2's flow 337@ .650.

 

[rumblefish360]

True on the W9 issue. MP says 300 cfm OOTB. Draw back? Pricey rocker arms, W9 intake and headers only. What else?

 

[Ironmike]

True on the W9 issue. MP says 300 cfm OOTB. Draw back? Pricey rocker arms, W9 intake and headers only. What else?

Well, ya have to run water lines, make or buy a water box with thermostat mounting. My buddy runs an R3 W9 headed monster, runs low 9's. like I said, its a whole different animal.

 

[rumblefish360]

YEa, I donm't know every in and out of the W9. A freind of mine is getting set to set one up. I'll see it as it progress'.

 

[70aarcuda]

I was wondering went the sale stopped....found this on their website...>LOL

 

[Cudafever]

WOW! LOL

 

[19DUSTER73]

Can a guy have them do just the port work?

 

[Ironmike]

Can a guy have them do just the port work?

Sure. Check out the website. They'll do as much or as little as you want.

 

[rumblefish360]

If you send them a bare head (or purchase a bare head from them) they can do just the CNC work if you wish.

 

[19DUSTER73]

Cool. I poked around their site a little bit. I'll have to contact them. I have a set of procomps that have been sitting on the shelf for a couple years.

 

[stroked340]

Cool. I poked around their site a little bit. I'll have to contact them. I have a set of procomps that have been sitting on the shelf for a couple years.

Good luck..hope they don't look anything like mine when they're done..

 

[19DUSTER73]

Swiss cheese?

 

[stroked340]

Swiss cheese?

p.m. me i'll tell ya all about it..