Last one to post in this thread wins!

-
Morning guys.
Got my pre-op this morning at 8:45 then drop my car off to have the rear end rebuilt and then shopping.
Supposed to be nice today
 
Mark Wainwright said:
Morning guys.
Got my pre-op this morning at 8:45 then drop my car off to have the rear end rebuilt and then shopping.
Supposed to be nice today
Click to expand...
Man! If you read that sentence really fast and aren't careful it sounds like you're going in for a pre-op on you rear end! I know hemorrhoids can be a PITA (see what I did there?), but I didn't think you'd need surgery for them, too!

:lol:

Have a good one, Mark! Hope the pre-op appointment goes well.
 
Haha I may do one day but so far so good.
Pre-op went well so my check in is for 9:30 am and surgery is 11:35 on Friday and home in the afternoon.
Apparently the gears in the rear end are 3:55's. I was told by the guy I bought it from they were 3:23. And the 3:23 are hard to get hold of. He may have it over the weekend but it'll be the same place as I left it up on the hoist
 
Morning guys.
Supposed to be a decent day. May be a good day to clean out the garage seeing my car is out of the way.
My oldest grandson is taking welding at school. He showed me a sample of what he did and it looked great.
He's looking at joining the armed forces and learn welding in there. It's all paid for so why not.
Have a great day
 
Mark Wainwright said:
My guy told me 3:23's are really hard to get here anyway.
Yes it is an 8 3/4 420 case.
I don't race it just a cruiser
Click to expand...
A new gear set shouldn’t be hard to find. Ordered a set of 8 1/4 3:21s to replace the 4:88s I had in there from Eastern Sales Chrysler Dodge in WPG. Took like 3 or four days. They come stamped with plus or minus from your original shim. Run the lead paint for pattern set back lash, the hardest part was crushing the sleave for bearing preload.
 
I wish the weather would settle down. Got off work, then got hit with pea sized hail on the way home.
 
To all concerned:both sides of border. In 5 days in Canada we will have a federal election, don’t know when our American neighbours next election will be. Doesn’t matter. The rule stands!
IF YOU DO NOT VOTE, YOU CAN NOT *****. NOT ONE F ING WORD. you had your chance to say something you chose not to so shut the f… up. My opinion
 
Ahoey said:
A new gear set shouldn’t be hard to find. Ordered a set of 8 1/4 3:21s to replace the 4:88s I had in there from Eastern Sales Chrysler Dodge in WPG. Took like 3 or four days. They come stamped with plus or minus from your original shim. Run the lead paint for pattern set back lash, the hardest part was crushing the sleave for bearing preload.
Click to expand...
The guy checked all over to find 3:23 and could only get 3;55's.
I even checked some speed shops and it was the same.
I stopped in yesterday and looked at the wear on the crown, no wonder it had a howl to it.
The crown had 1968 stamped on it so looks like the whole rear end was replaced during the car rebuild.
The car was an original 273 car so probably had a smaller rear end in it.
It might be ready today but more looking to Monday.
I did get a chance to give the garage a good cleanout and looks much better.
Have a great day
 
A guy was about to get a ******* and she says "how cute you have a tattoo on your dick"
He tells her I had the place I was born tattooed on it.
She says "Oh you were born in Swan?"
He said no Saskatchewan
 
You must log in or register to reply here.
-

Back
Top