Search results for query: *

Hi. I have now been driving it this summer. Everything works like it should expect for the OD. I have OD and LU on 2 switches. When engage the OD it is slow to engage but when done i can go full throttle and no slip. When engage LU it is instant. What am i missing? SHiftkit is mounted. 1.2...

Hi you all. In the process on renovate an 42RH from a dakota 3,9 to put in my car. I have read a lot of threads about the car work needed to be done and finally started. On the gearbox on the left side close to the split right over the colerfitting. Whats it for. Messure pressure. Second i have...

Hi out there. Am i the only one having problems with borgeson box with doug headers D453. It is less room for the header after the change. much moore room to the frame. I also had to move the pump plate so the pressure hose will fit. And make a new pressure hose. Did a simple mesure and lined...

Hi Guys and Gals. 340. Flattop. Aluheads. 2 plane intake. 10,5:1 comp. street cam hydraulic very moderat. Carb set at nr 3 in the chart. Goes perfect at idle, light throttle, transition @ ca 0,95 to 0,97 at lambda. But light stumble to WOT. Not tested next hole on acceleratorpump yet. Then lean...

is there a template to know where to put them?? Johan.

My sockets are broke. Looking for the press in socket and pigtail. Been looking around but cant find. Any info on where to get something that will work Johan.

Hi. 340. HFT lunati. Lifters summit 2011. Most is stock inside. CR 10.2:1 . Car been sitting for a couple of weeks. Noicy at start up but get better after a while. Trying to figure out what to do. In the process i see that the grove on the lifter is leaving the hole for the oil when it starts...

Hi Guys and Girls. I want to put back my mouldings on top of the fender, door and qourter panel. I have the mouldings but not any nuts, retainers, retainer w/seal, seals, or clips. Dont know how they look but i have some numbers from car parts catalog. Dont get any by searching the internet. By...

Hi. On my 67 dart someone updated ignition to mopar stuff before me. Tryed to find but i turn to you. In the foto i would like to know wich color is + and -. Can i messure to know. It is the conector clossest to the dist. One is brown with tracer and one is grey with tracer. Thanks from...

Hi. A couple of my roller tip rockers bushings have failed on the axel with big çlearences. Engine 340 is nearly stock with a bit hotter cam and springs. I have NOT done any oiling mods. Oil is coming when the camholes line up and i pump with electrical drill. Should i have done the groove in nr...

Hi guys. I am mounting green bearings and that worked nice. The the lockring or collar is 0,20mm or 0,00787" pressfit. Cant get it on. Preheated with a heatgun but dont work. Do i need a blowtortch and heat it redd or almost redd? Johan

What will fit in this hole. Dont want to ruin the hole. Been googling but cant find anything

Hi Guys. The motor has nr 2822963 for 66-67 AB Variable early White SW plate as i under stand. Only 3 wires. cant figure out howe to put the wires. Red +12v. Blue +12v constant so it will go to park. Brun +12v to get it going full time.The switch and bulhead conector is as the wiring diagram...

Hi. When benchtesting it works fine but dont go back to park just stops when shuts down. Test with the cover of and wvhen i make contact betwen green and blu it work. Are the blades you se in the picture suppost to be in contact at all time exxept when the mecanic insade pushes it away.

Hi fellow moparfans. I have a 1967 dart 4pot front disc brake with 489 58inch wide rear drum. Want to convert the bolt pattern. Weld the holes in the rear shafts and redrill for 4,5. Not that easy in the front. Want to keep my calipers. Is there any disc and hub that will fit my spindel or...

Can i get some help. Tried myself and with a friend with this: DodgeCharger.org -- 1967 Fender Tag Decoder MyMopar - Mopar Forums & Information - 1967-1968 Mopar Fender Tag Decoder thanks

Hi. I am looking for the trim that has the fender turn signals and go all the way back.

Hi. Some thoughts before the winter. Antirollbar front.Dont have any at all. What about addco New power steering box. Std from jimsautoparts and firmfeel fast ratio pitman and idler? Or bogeson and Std pitman and idler. Any other suggestions are welcome. Not a race car. Want good sreetmaners. Johan

Hi. Why is there a zipper on the rear window. Should i remove the window first Before i move the top down. When its in down position the cover will have a lite bump. Is that normal. Seems that the cab rests on the inner wheelwell so it cant go any lower.

Hei. If i turn it to the left the wiper goes superfast. 1st to right slow 2e to the right i Think it is faster the longer to the right. Dont really have a turn of Point. Any know the correct setting?

Hi guys. Will that on my 340 clear the hood with GTS aircleaner on top.

Hi. My exhaust backside interfer where i painted the green color. I can solve this by taking a grinder and lover it by 9mm to make room. Anyone ells seen this problem???

Hi guys and Girls. Do i need to have them mounted when i put the Engine back in my Dart? I have this set up. Cant find anyway to put the left one in now when the Engine is in. Is there any shorty.s that leave Moore room. Johan

Hi guys. Looking for Pictures of the Engine bay unrestored if possible. I know that the Engine color is red on the 273 or? Like to make it look like 1967 even if it is a 340 1972 duster Engine.

Hi. If i understand it is external balance with weights on the torque converter and a bulge on the thing in front. Correct???? I am going for +0,030 pistons flattop .STD rods. STD cast crank. Can i cut the weights from the torque conv for it to be 0 balance and put weights on the flexplate...

Hi. On my car when I will warning flash the knob is in the centerposition and of is downwards. Correct? Johan

Hi. Will these work on an 340 in my dart with PS? Johan

Hi guys. Found this on a car. Whats wrong or? It is on a dart gts 1968. Johan.