Search results for query: *

Where can i buy lower front shock bolts for my 70 Duster? 7/16 x 14 x 2 1/4 with a 1 1/2 shoulder

Put leaf springs on my 70 Duster can anyone tell what to torque the shackle bolts,ubolts and the bolt in the front of the springs I believe they call it the pivot bolt to

Where can I get torque specs for the front suspension on a 70 duster

Does some one have a close up photo of where to take the measurements for ride height on 70 Duster. Is it from the lower ball joint to floor and adjusting blade to floor. Then subtract the two. What are they meaning by adjusting blade

Can some one tell me what the ride height is on a 70 Duster . Has 15 inch tires .I am getting what they call bump steer under heavy acceleration. Going to check ride height and re align . Also installing different bushing in upper control arms to get more adjustment.

Taking my Duster to have it aligned . Any know what the specs are on the alignment. Also would changing to tubular upper control arms give me more camber?

The idler arm i purchased came with two felt washers and a metal flat washer.Does the flat washer go on the top or bottom of the idler arm when installing the bolt through the k - member Or should they be two flat washers one on top one on bottom.This is for a 70 duster small block

I have the hood hinges off of my 70 duster. I have a set of new low tension springs that i have installed but they will not hold the fiberglass hood up.Is there a tool or procedure to put these springs on to make sure they are wound tight enough so as to give me more tension so they work...

The steering box on my 70 duster has a lot of play.I am looking into where to have it rebuilt and maybe change the ratio.Has anyone went to the different ratio and how do they like it or should just stay with the original ratio.Any info would be appreciated

Car is a 70 duster with new mp torsion bars.I loosen the nut on the lower control arm.I then turn the adjusting screw in.I do both sides the same.I am taking a measurement at the center of the wheel to the fender on each side.I started at 25 1/2 on each side after adjusting i take the...

I have a 340 duster with the original u joints .Is there an upgrade to a stronger u joint or could someone possible have a part number.Auto parts stores seem to have a hard time looking them up.The differential is a 83/4 741 case 391 gears

I am getting ready to install aar fiberglass hood.I believe i have a set of feather duster hood hinges.Could someone possible post a pic of one.I do not know how to post photo of mine.I have the original set.The springs on the original hinges are about twice the diameter of the new hinges.Any...

Does anyone sell the felt washers and bolt for a 70 duster idler arm without having to buy the whole thing

What do i need to purchase to change the adjustable axles out to the new type axle bearingsin a 70 duster.I believe they are called green bearings.Does someone sell a kit.Thanks

Purchased springs from espo no instructions and can not get in contact with them.Is there a right and left to these new springs.The factory ones had a right and left.Thanks

Is there a procedure for installing leaf springs such as torque specs on mounting plates and shackles.Should everything be tightened sitting on floor.Whats the best way.Putting in 70 duster

Looking for best avenue to replace the leaf springs on my 70 duster.It is a 340 car with the correct springs.Would like to replace with the same kind.Anyone have any suggestions on where to purchase and best bang for your buck

Installing original front sway bar back in my 70 duster can't find the mounting brackets.Can you buy these.

Where can i purchase factory service manual 70 duster.

Any one have alignment specs for 1970 duster 340 car stock suspension.Also am confused where to take measurments for ride height.

Can anyone explain clocking or indexing of the torsion bar 70 duster.Also where should the adjusting arm on the lca be positioned.All the way down on the adjusting pad where the adjusting bolt comes through .This seams to change how far the adjusting bolt sticks out of the lower control arm when...

Can some one post a photo of the tie rods and center link for a 70 duster to ck and see if mine are correct

Any one get a steering column done or buy one from norms speed shop in wi.How was the quality

I am working on 70 duster .I am working on the front suspension.When i put the outer tie rod through the lower ball joint the stud on the tie rod is at an angel when you draw the nut down it will pinch the boot.Anyone run into this problem or is this the way they are:banghead:

Getting opinions on best torsion bars and where to purchase .Any discounts for a body members

I am getting ready to repaint my steering column in my 70 duster with floor shift.I need to disassemble it to paint it.Where can i get diagram of it and is there any thing i should know before tearing this apart.Where can i get parts if i need them.Any information would be greatly appreciated

I have a 70 duster with disc brake set up with sbp.I purchased a suspension kit some time ago. I put in new ball joints and tie rod ends from mancini.The outer tie rod ends will not go into the lower ball joint assembly.It looks like the tie rod ends are wrong or the lower ball joint assembly...

Getting ready to buy torsion bars any suggestions on what brand and size to buy.going in 70 duster 340 have 892 and 893 bars in it now one is damaged is why i am changing them

Can anyone tell me if there is a left and right leaf spring.These are factory 340 leaf springs.Any suggestions on leveling the car.High on right rear.

Can any one tell where to get the best torque boxs and frame connectors for a duster