Search results for query: *

I have a crewcab 2500 The kids like having the rear dome on so I replaced the stocker with one from a higher trim level that has a switch in it Run a keyed hot to it and done, right? One my truck there was a ground on the left post, and a switched hot on the center (that on gets power when...

i added a rear blade to the plow over the summer and now that ive been using it, ive noticed i dont like the switches the switches are the most basic normally open momentary switches one wire in, one wire out now, what i want is either one switch with two positions, or two momentary push...

With the seasons changing I've been putting the plow truck through the paces I found it had a strange issue, wel several, really The first thing I noticed was that my back up light were not working properly No big deal, I'm running a few LED spots hooked up to the OEM back up wiring, so...

Hey guys, I need 4 of these little doohickies to connect a switch, but I don't know what they are called They look like a spade connector, but are only half the width of those

morning Gents i just installed another gauge in my duster and i thought to myself, what a rats nest this wiring is i think my duster only has 4 spots on its fuse panel and it uses those little glass tubes, kinda like the one Doc Brown used to get the plutonium into the flux capacitor, only...

so the duster has been running a bit rough, not as powerful as it should, sometimes backfiring on shifts, and getting hard to start once warmed up I figured id check the simple things first, and took apart the fuel filter found a little bit of crud in there, but not bad for running a fuel tan...

this is on my plow truck it has a volt meter which used to stay pretty steady at 13-14 today i was out plowing and it looked liked the voltage on the gauge dropped way more then usual when i run the hydraulics, down to 8 what really caught my attention is that it takes longer and longer to...

hey guys im working on the family car, 2013 CX-9 with the regular halogen headlights H-11 bulbs my passenger side bulb had burned out (i thought) and when i went to replace it i noticed the socket had melted a little on the contacts no biggy, ran out to vatozone and bought a new one cut the...

ive been driving the bronco plow truck and it does not have intermittent wipers (neither does the duster, but it doesnt bother me much there because i dont drive it in the rain/snow on much...at least not on purpose) so, is there any way to change out the switch maybe? (i did that on a mitsu...

71 duster, originally a /6, now a 408 auto been about a week since i drove the car, and when i went to take my boy to school this morning i noticed my turn signals werent working when i turn them on the bulb will light up, the indicator on the dash will light up, but both will be on solid...

I have a 2 speed wiper motor on my duster it looks like the thingy that is mounted on there, which makes it run slow, is missing (all I have is full bore) so I'm guessing if I find one of those doohickeys, I could install it and get slow going again? EDIT:MORE INFO si I just...

so I'm thinking about adding foglights to my 71 duster I don't want to mess up the looks of the car, so here is my thought...could I replace the small running lights with the indicators, which fit in between the headlights, with a set of foglights? does anyone make a bolt in replacement...

hey guys I am looking to hook up the electric choke on my 600 CFM carb (eddie) im supposed to have a keyed 12 volt source is there a wire that is preffered? the coil seems like the most obvious choice but I don't know if its a good idea to tap into the positive wire going to that...

hey guys I noticed an interesting problem over the last few days it appears my tail lights stay on when the ignition is off of course over the timespan of a night this is enough to drain the battery and ive found out that modern cars don't have the juice to crank the old V8 around...

so, Im finally making some leadway on the duster I dropped the 360 in and I was in the process of hooking up all the wires when I did this it sure felt right and the wires "fall" in that spot naturally (the blue and green ones) but that left me with these two wires, about a foot...

I can get rid of the ballast resistor right? (I have a 71 duster, that came with a points ignition /6 and im dropping in a 360 with a skip white distributor) the ballast resistor has 2 post with 2 wires each can I just cut them at the harness, splice all 4 together and tape it up?

hey guys I am about to swap my /6 with a 360 (the car is a 71 duster) I am planning on using a skip white style HEI in cap single wire distributor will the existing coil from the /6 work or do I need a different coil aswell ? thanks guys

hey guys im prepping a 360 to swap into my 71 duster the 360 is a 75 (electronic ignition) and the car is a /6 with points the distributor cap on the 360 is cracked so I figured I might as well replace the whole thing to make the conversion easier Im considering one of the 2 wire...