Search results for query: *

...four years since I screwed it together, can't recall the dynamic CR or the IVC on the cam. Seems like calculated dynamic was around 8.2:1 I run 4* more initial timing than spec on the TBI in ambient temps of up to 115 degrees, a 195 T-stat and 87 octane with no rattles. It has fresh air to...

Posted this in fuel/air too, trying to increases my chances lol.....my apologies. I have a TBI LA360 with a non-stock compression ratio, need to take the timing control away from the PCM. To do that I need two separate signals, one to trigger the ignition, one to the PCM so it will trigger...

Not sure exactly where to post this, here, Magnum swaps or the ignition section, but here we go. I have a TBI LA360 with a non-stock compression ratio, need to take the timing control away from the PCM. To do that I need two separate signals, one to trigger the ignition, one to the PCM so it...

The stock cam retainer plate has a relief on the back, aligns with the right bank galley, and the galley plug had a hole for lubing the chain. Replaced that with a tensioner, which has no relief on the back, and the plug the machine shop installed has no oil hole. Chain/top gear gonna run too...

Stock retainer locks 7* or 10*? '90 360 btw........

Been looking for retainers that'll fit '90 308 heads. Type 1990 360 into Summit's or Jeg's search engine and I get nothing. One goes to '89 and the other '86. Far as I know they're the same, but not 100% certain. Jeg's has some Comp retainers, but they seem pretty generic. Fits Ford, Chevy...

...pointer on a degree wheel should be to the right side of the TDC mark at .050" lift? Installed centerline's 111, had to advance the cam a full 8* to get there. Helped the .050" opening number, at least it's at 12* atc instead of 20*. Watching the indicator, the closing point is way screwed...

Thought this was pretty cool.

Wreck on I-20 just outside of town. The Ford blew a tire, crossed the median and hit the Dodge head on. There were four guys in the Dodge, the two in the front seat were killed, the other two critical. A woman and three passengers in the Ford, all came through alive. Not trying to be morbid...

107* here today, and it's been so dry I seen two catfish pickin' the ticks off each other.

My '97 LHS has a miss. 3.5 V6. Engine's in good shape, even comp across the cyls, uses no oil, plug color looked good etc. Has about 95,000 miles, been garaged/pampered since new. Had a little putter at idle to begin with, has progressed to a noticeable miss under load. Gas mileage has dropped...

Some folks will stuff a Cummins in anything seems like:cheers: Thought it was a cool pic.

........there's not a hot rod of some form in my garage. Dang, guess I'm getting old. It's no A body, but it's a Mopar, and I'm gonna miss it. Sold this to my nephew for $2000, been sitting collecting black widow spiders and dust for almost 6 years, hasn't been started in 3 years due to a...

Broadband is all that's available where I live, tired of waiting for news stories etc to fully load, and tired of being bombarded with ads period. Can't watch a news vid {Or what passes for news these days} without watching the stupid commercial first, so who makes the best ad blocker...

...on them look like somebody crapped on the flanges and smoothed it off with a hacksaw. Tired of substandard parts because I drive a Mopar. To my knowledge TTI doesn't make block huggers, know of ANYONE who takes pride in their work or am I going to have to build the #%*& things myself?

These are '90 360 pickup 308 intake ports, and as you can see the mismatch is awful, about 3/16". This gasket is very close to the Air Gap's port size. If I open the port to gskt size, looks to me like that will only induce more tumble on the backside of the pinch. I'm going to pare down the...

Few choice words in this, don't watch if you're easily offended. http://www.killsometime.com/videos/8161/Dad-Gets-Revenge-On-Daughter-For-Facebook

Sounds like me and my wife.

Hmmm.

.........but funny none the less.

........no electric bill would be nice. New invention. I assume it's still under development, doesn't give a watts/sqft, but I can see the potential. http://www.ted.com/talks/lang/en/justin_hall_tipping_freeing_energy_from_the_grid.html

Was out in the yard today letting the dogs run around a little. Heard a single yelp, turned around and a coyote had the wife's chihuahua in it's mouth, already headed for the pasture. {I have 20 acres} Bold sob, broad daylight, and not 10 yds from me. Came right up in the back yard and snagged...

Heard this advertised on the radio. www.easywater.com Anybody have or seen one used? Looks like an offshoot of a fuel ionizer to me, and we know how well those work..........{not} Judging from the wire wrapped around the pipe, it creates a magnetic feild which supposedly realigns the crap...

My old Gateway desktop bit the dirt. Been looking, but it seems there's 97 different brands and configurations these days. Numerous processors too, up to six core, etc. I'm on the wife's new laptop, she's using her old one, she ain't happy about it either. What's good these days? Mid price...

Once upon a time a man asked a girl to marry him. She said "NO!" And he lived happily ever after, and worked on his hotrods, hunted, fished, played golf, drank beer, got laid regularly, scratched and farted whenever he wanted. The End.

Have a line on a decent '97 Avenger with a Mitsu 2.5 V6 for cheap. Run around town car for the wife. Anybody have any experience with/owned that motor? I've seen 3.0's puffing blue smoke, because of valve guide issues from what I'm told. Any troubles with the 2.5?

The LA roller architecture is supposedly the same as a Magnum, right? How much lift will the factory setup swallow before the lifter hits the guide link? Eyeballing with the stock cam on the base circle, looks like the link limits lift to around .520" with a 1.5 rocker.

Wife says I'm self centered.......just because I turn those "studded for extra pleasure" condoms wrong side out..............

What's a rust free '61 Lancer 2 dr going for these days on average? Found one, guy wants an offer. Needs a complete resto, interior is complete but trashed, body is straight, but needs paint etc., glass is all good. He says it runs, which could mean on all six, or maybe just two or three...

In the market for a builder Lancer or Valiant wagon that's fairly complete. Got one you'd part with? Preferably within 6-700 miles of Odessa Tx, but might go further for the right car.