Search results for query: *

This is a OEM 1969, 1970 Headrest Bezel #2942847. It is original, not a china knockoff. It's not new, but is in very good used condition. $15.00 shipped to CONUS.

I like it! :thumbsup:

I see. I'll have to do a little research on that. Thanks again!

Small block Offenhauser single plane intake manifold. All threads are good. Asking $150 plus shipping.

You did not say what car you have, you want an orginal looking Mopar battery, A Body should be Green, I believe that Yellow would be an E Body.

I hear ya

no, it's probably closer to $2k, but I'm just saying if his rods need to be resized or if he needs new rods, that subtracts from the cost of the stroker kit differential.....

Greg

No, like an autobody paint supply store.

Solved the issue. I had swapped the rear tires from side to side before opening day. Just a habit I had gotten into over the years. Apparently these Goodyear tires, even though they don't have directional arrows on the sidewalls, are directional. First test run at Winterport Dragway this...

Thanks! I also hate the appearance of worm drive hose clamps. On the LA engine, I had put heat shrink on them and painted them black to mask the ugly. I've never used them, but that's what I intend to use on the heater hoses since both ends have a threaded fitting for removal. I'm going to...

That was close :thumbsup: :lol: KPFM pizza and humor aplenty

pretty much level. both are about 25.25", but the rear tires are over an inch taller (215/70's) that's probably the bigger reason I don't want to raise it up more, is I don't want the nose up look. had I realized it would be sitting this high, I probably would have bought the magnumforce...

Look at the cold cranking amperage and amp hour rating, and make your decision from there.

I went for a few groceries hoping to miss the rain. Well I pushed my luck and as I was checking out in Wal Mart I heard it just pouring on the roof of the building. I looked at the radar and no breaks in the action for a while, so I got drenched. No shower needed now!! :BangHead...

NIB Edelbrock valve spring set. Part # EDL-5777. $100 plus shipping.

Did you install your pistons backwards too like UTG? Just kidding! Glad you found the problem. It happens to the best of us I have the same fixed 7 blade. Worked great keeping this cool with no shroud, but I recently switched to a viscous clutch fan to gain some freed up HP. I might need to find...

Will a 235/60/15 fit on the front of my 68 Dart with a 15" x 7" with 3.5 back spacing or am I at the max with a 215/65R15. Getting ready to buy tires.

Got.no C pillars! And it has reverse lights. Anyone know if the guitar pick GT is available.

So the good aircraft remover still exists? Yea the stuff here in the golden shower state does nothing but make a mess. I can try the oven cleaner first before anything. I have a diesel burning pressure washer that should help! Other than the orange stuff, the rest is very thin and a quarter...

So. Seems only the one in Escondido is changing. Whew

1969 RHD BUICK GS400 CONVERTIBLE ONE OF ONLY 1720 MADE THE CAR WAS BUILT IN FLENT TEXAS USA THE CAR WAS IMPORTED THROUGH LOCKHART MOTORS ON THE GOLD COAST NEW FOR A LOCAL BUSINESSWOMAN THE CAR WAS STORED FOR 20 YEARS.

Be sure the thermostat you have is a high flow one like this Stewart Components one, not all are.

Sad. West Coast Pizza Company Replacing Killer Pizza From Mars In San Diego's North County - NewsBreak

NIB small block Speedmaster head stud kit. Part #746-PCE279, $60 plus shipping.

Unfortunately, those cars make really good cruisers. And it is much easier to buy a newer car that is also faster than most old cars and drive it than to try and modernized the old one. And if you want to keep the old one stock, it makes the newer cars even more enticing. Not saying it is...

Why would it matter on a run stand which way the air goes through the radiator? Answer, it doesn’t. It will make the shroud a little less effective though.

What brand/model? Thank you

A good street piston none the less and inexpensive at cnc motorsports. Most forged pistons have gone the 1/16th ring package or smaller. Maybe some older trw type pistons available in the classified section with the thicker ring package

This all came about because I scored the original boster and was planning to upgrade her to the dual pot. But, the 13" wheels look stupid, and since I found the 14" 4.5 circle Astro Slots which require a bolt pattern upgrade. OEM engineers got alot of stuff right, and after going through some...